Ikea Dishwasher Control Board

The Switch Assembly is an OEM replacement part for Frigidaire dishwashers. It contains a touchpad and electronic controls that operate wash cycles and drying features.

Causes of a faulty switch assembly can involve water exposure inside the door control area leading to circuitry corrosion over time.

Symptoms of a bad switch assembly include:

• Inability to select or advance through wash cycles
• Failure to heat water or activate the pump
• Erratic or stuck temperature readings
• Unresponsive buttons

This OEM Frigidaire replacement part is also compatible with dishwashers manufactured by Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Electronic Control Board is an OEM replacement part designed for Frigidaire dishwashers. It houses the integrated circuitry that monitors and directs all functions of the dishwasher like temperature, cycles, sensors, and component operation.

Symptoms of a bad electronic control board include:

• Cycles failing to start or not advancing properly
• Lights and displays not illuminating or responding as expected
• Inconsistent or no heat during the drying part of cycles
• Unusual noises or vibrations coming from internal components

Causes of a bad board can be moisture exposure damaging circuits, power surges disrupting chip performance, or natural component degradation over extended use.

This OEM Frigidaire control board is also compatible with models produced under the Electrolux, Gibson, Kelvinator, and Kenmore brands.

This genuine replacement part is a control board for Whirlpool dishwashers. The control board is the main circuit board that controls the dishwasher's main functions. If the dishwasher is no longer turning on, or is not draining properly, it might be time for a new control board. Luckily, replacing a control board is an easy process.First, remove the outer door panel of the dishwasher by unthreading the mounting screws. Lift the control panel up and disconnect the wire touchpad harness from the control board. Then use a flathead screwdriver to release the locking tab and slide the control board housing to the left to detach. Remove the wire covers. Once removed, take note of the orientation of the wire connectors and disconnect them from the old board. Install the new control board by reconnecting the wire connectors to the appropriate terminals. Align the wire covers and pop them into place. Insert the control board housing tabs into the slots of the mounting bracket and slide the housing to the right to secure. Reinstall the control panel by attaching the control pad wire harness to the new board. Align the panel and rethread the mounting screws to secure. This replacement control board is compatible with Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand dishwashers.

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

The User Interface is an OEM part for Frigidaire dishwashers. As the user interface, it allows users to select cycles, options, and monitor dishwasher status.

Causes may be due to wear and tear over time, water damage, or shock/impact. This OEM Frigidaire part replaces the entire control panel assembly to restore full functionality.

Symptoms of a bad user interface include:

• Unresponsive or nonfunctional buttons
• Blank or dead display screen
• Inability to select cycles or options
• Erratic operation and unexpected behavior

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This main electronic control board governs the appliance's user interface and cycle functions, restoring responsive controls and correct operation when the original board fails. Replace a faulty control board to correct erratic or unresponsive behavior. What it does:

• Receives input from the console and sends control signals to relays, valves, motors and sensors.
• Restores normal cycle selection and timing when a failed board prevents the appliance from starting or completing cycles.
• Addresses symptoms like unresponsive or non-working buttons, blank or erratic displays, and unexpected program changes.
• Interfaces with safety and feedback sensors to coordinate appliance functions.

• Always disconnect power to the appliance before replacing the control board to avoid shock or damage.
• Handle the board by its edges and avoid touching circuit traces or components; the board is static-sensitive.
• Note connector locations or photograph wiring before removal to ensure correct reassembly.

The Control Board is an OEM replacement part for Frigidaire dishwashers. Located inside the cabinet behind the control panel, the control board utilizes integrated circuits and electronic components to regulate all dishwasher functions. It receives input signals from the control buttons to initiate and monitor the wash cycle. 

Causes of a bad control board can include failures of electronic components over time, voltage fluctuations that cause circuit damage, or moisture infiltration leading to corrosion.

Symptoms of a bad Control Board include:

• Dishwasher fails to start or stops mid-cycle unexpectedly
• Lights or displays on control panel malfunction  
• Inability to select options or cycles
• Complete non-responsiveness of control functions

This board is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

This Electronic Control Board is the appliance's central control module. It interprets inputs from sensors and switches and directs power to motors, valves, heaters, and fans to run cycles reliably when the original board has failed.

• Manages overall operation by processing signals and executing programmed cycles
• Sends power/commands to components such as motors, pumps, fans, heaters, and valves
• Typical symptoms of a failed board: no power or won't start, unresponsive controls, cycles that won't advance, intermittent shutdowns, or error codes
• Useful when diagnostics point to control failure after ruling out fuses, switches, sensors, and wiring

• Disconnect power before servicing; turn off water supply if applicable
• Use ESD protection and handle the board by its edges
• Photograph/label all connectors; move harnesses one at a time and transfer any jumpers/settings from the old board if present
• Mount securely, reconnect wiring, reassemble, then run the unit's diagnostic/self-test per the service manual

The Cntrl-Elec is an OEM part for Whirlpool dishwashers. As the control and electronic component, it governs all of the major functions and operations of the dishwasher. The control board contains integrated circuits, microprocessors, and electronic components that facilitate cycles, temperature regulation, safety features, and user input.

Over time, the electronic components inside the controller can degrade or become damaged. Environmental factors like surges, fluctuations in power, and other electrical issues may also potentially cause failure. 

Symptoms of a bad controller can include:

• Not operating or cycling at all
• Inability to start or stop cycles
• Fault codes displayed
• Issues with heating or drying
• Buttons or control panel not responding

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.