Dishwasher Control Board

Indicator light would blink three times, make a sound, but the dishwasher would not run. After making sure there were no obstructions, no problems with seals, filters, and latch clean, I cut the power off and back on. The Dishwasher worked for a few more times. After that, cutting the power off and on no longer worked. I figured out what buttons to press and hold to find the error code (start/stop and cycle select), saw code 815, and then did a "hard reset" by pressing and holding other... Read more

My GE dishwasher (GDT605PMM0ES) had started going in and out of service but if I unplugged it and plugged it back in it would work a few more times. Then one day that old trick didn't work anymore. Looked at what might be the issue on the internet and most signs pointed to the configured service machine control board or the configured Ui board. I ordered both, not really which was bad, but started with the Ui board first because the service machine control board showed it was receiving... Read more

The fix was very easy. Control assembly is easy to access by removing 5 phillips screws. Unplug the wiring from the old assembly being careful to note which wire goes to which connector. Install the new assembly and connect the wiring. Read more

The control went thru a month or so of erratic behavior; the display would come on and flash and beep without any input on my part. Then it died completely. I did a little research on the GE website and determined likely cause waa a defective user interface board. I found AppliancePartsPros.com and contacted their tech support, who directed me to check the output of the control board across 2 pins for 13.5v DC. I did this, and measured 13.8v, so control board was good. When I reconnected the... Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

Replaced the Timer and Solenoid in 30mins very easy. APPros, fast shipping is amazing! Read more

Replaced the timer and drain solenoid (timer had stuck in "solinoid active" position long enough to burn up the solenoid). Complete the project in two stages on two separate days: 1) replaced solenoid, which took about 30 minutes, 2) replaced timer. Accessing both was straight forward on this simple design dishwasher. Removed the kick panel to access the solenoid. Removed 3 screws and a circlip to remove the old solenoid. Reversed the process to complete this part of the repair. The... Read more

After reading through a few forums, I narrowed the problem down to one of 3 issues, the door latch, the switch assembly (control panel), or main control board. I rolled the dice on the switch assembly first. The main reason I did this was my belief the door latch was okay and because the main control board is more expensive. The removal and install of the switch assembly was pretty easy for me, and I would expect for most people that know how to use a screwdriver. When I removed the old... Read more

I had to remove the dishwasher about 6 inches then remove the door springs and remove the door. Next was to open the cover to reach the circuit board and remove it. The new board was put in and attached the plug. and put the door back together and reinstall the door and springs. Turned the power to check that the lights came on. After confirming I again had power, I turned the breaker off and reinstalled the dishwasher in the cabinet and restored power. Lastly I ran the machine to ensure that... Read more

GE Dishwasher would beep intermittently over the course of about a month. It then began to shut itself off. I would have to reset the breaker to get it to come on. Eventually, it stopped working altogether. After confirming that I did in fact have proper power to the appliance. The main control board had power and was in good shape. I then traced the problem to being a bad UI board. Which I found with the help of a nice lady over the phone at AppliancePartsPros.com. Read more

Just removed from front and the console. I wound up replacing the control board because the technician that I had come out said that's what was wrong and it would cost $250 to fix. I replaced the control board and it didn't fix the problem. After doing more research and searching out the error codes, I discovered I had to replace the console. so i did. I was able to return this control board and buy the console. That return policy was fantastic. I was so worried I was going to have to eat the... Read more

I went to appliancepartspro.com and found out that the problem could be the main circuit board. I went on and ordered the part, knowing it could be returned if necessary, but it was like music to my ears when I installed the part, myself, and turned the power back on. Easy. Thanks appliancepartspro. Read more

The part fit exactly like the old existing one. Read more

• Will not dispense detergent

Replaced control board. This did the trick! The dishwasher works great again. Read more

Replace the control board! Read more