Jenn-Air Cooktop Parts

Replace a clogged or damaged vent grease filter to keep your appliance drawing properly. This filter captures airborne grease and cooking particles to protect the blower and help maintain effective ventilation over your cooktop.

• Traps grease and particulates pulled through the ventilation stream during cooking
• Helps protect the blower and internal components from buildup
• Supports proper airflow and smoke/odor capture from the cooktop area
• Replace if torn, warped, heavily saturated, or when cleaning no longer restores performance

• Disconnect power to the appliance before servicing
• Open the vent grille or filter access and release the retaining tabs/handle
• Note orientation; seat the new filter fully and latch securely
• Do not operate the vent without a grease filter installed

This gas surface burner cap sits on top of the burner head to shape an even flame and shield the burner from spills. Replace a missing, chipped, or warped cap to restore proper flame pattern and appearance.

• Directs and evens the flame across the burner for consistent heating
• Shields the burner head and ports from spills and debris
• Helps promote reliable ignition when properly seated on the burner head
• Common signs it's needed: uneven or yellow flames, delayed ignition, flames lifting or noisy, visible chips/warping

• Ensure the cooktop/range is cool; disconnect power and shut off gas if working near igniters
• Lift off the old cap and clean the burner head/ports; do not enlarge or damage the ports
• Place the new cap on the matching burner, centered and seated flat; do not interchange sizes between burners
• Light the burner and confirm a steady, even blue flame; reseat the cap if the flame is uneven

This factory window pack assembly creates the sealed, insulated glass window in your oven door. It restores a clear view into the cavity and helps the appliance hold temperature when the original window is broken, cloudy, or damaged.

• Forms the sealed, multi-pane window within the oven door
• Helps contain heat and maintain consistent baking temperatures
• Restores visibility into the oven cavity
• Common symptoms: cracked/shattered glass, fogging or streaks between panes, rattling glass, heat escaping near the window area

• Disconnect power and allow the oven to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass vertically and support the edges
• Door removal and partial disassembly are typically required; keep screws and trim organized
• Transfer any reusable brackets/insulation per your model's service information

This Frame-Glass is the outer glass panel for the oven door, restoring a clean appearance and helping retain heat while keeping the oven cavity visible. It replaces damaged, cracked, or chipped outer door glass. What it does:

• Provides the outer glass surface of the oven door for safe viewing of food while cooking
• Helps maintain oven heat and improve energy containment when the door is intact
• Replaces cracked, chipped, or shattered outer door glass that can affect appearance and safety
• Restores a sealed, clean-facing surface for the door assembly

• Disconnect power to the appliance and allow the oven to fully cool before beginning
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires removing the oven door and detaching trim/fasteners; keep track of screws and clips

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks

Replace a damaged or missing selector knob to restore smooth, precise control of your appliance settings. This knob fits onto the selector switch shaft so you can easily turn and choose functions as intended.

• Attaches to the selector switch shaft to turn and select functions/settings
• Replaces a cracked, stripped, wobbly, or missing knob
• Helps when the knob slips or won't stay on the shaft
• Restores proper alignment with panel markings for accurate selections

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off; if tight, gently wiggle while pulling
• Align the new knob with the keyed/flat on the switch shaft and press fully into place
• Verify smooth operation and correct pointer alignment with panel markings

This LP conversion kit adapts compatible gas appliances from natural gas to liquid propane. Proper conversion helps ensure safe ignition, correct flame size, and consistent heating when your installation uses propane instead of natural gas. What it does:

• Converts the appliance's gas system from natural gas to LP/propane
• Matches burner/orifice sizing and regulator setting to propane fuel characteristics
• Helps correct symptoms tied to the wrong fuel: tall yellow flames, sooting, weak heat, uneven burner performance
• Required when connecting the appliance to an LP/propane supply

• Includes LP conversion kit

• Must be installed by a gas technician; follow local codes and the model-specific instructions
• Shut off gas and power before starting; verify all connections are leak-free with an approved leak-detection solution
• Replace the specified orifices and set/convert the pressure regulator to LP as directed; apply the provided LP identification label
• After conversion, verify flame appearance and manifold pressure

This radiant surface element restores proper heat to a glass-ceramic cooktop burner. When the original element burns out or develops hot spots, replacing it brings back steady, controllable heat for everyday cooking. What it does:

• Generates heat for the selected cooking zone beneath the glass top
• Works with the surface control to cycle on/off and regulate temperature
• Helps deliver even heating across cookware
• Common fix for: burner won't heat, heats slowly or unevenly, only part of the burner heats, visible damage on the element

• 1 radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Support and handle the glass top carefully to avoid damage
• Note wire locations and transfer any mounting hardware from the old element
• After reassembly, test the burner on low and high settings

This surface radiant element sits beneath the glass cooktop and generates heat for one cooking zone. Replacing a failed element restores proper heating performance and dependable temperature response on the affected burner.

• Supplies electric heat to the selected surface burner under the glass top
• Common symptoms: burner won't heat, heats weakly or inconsistently, or only part of the ring glows
• Visual damage (burn spots/breaks) or an open reading on a continuity test indicate replacement
• Similar symptoms can also result from a faulty surface switch or wiring—diagnose before replacing

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Note wire positions and bracket orientation; move wires one at a time to matching terminals
• Support the glass and avoid stressing the element; test operation before final reassembly

The Knob is an OEM part for Whirlpool ranges. As the user interface for selecting functions, these knobs allow for precise temperature and burner controls.

Causes of a bad knob can include damage from harsh cleaning chemicals, loose or worn retaining screws, or normal wear and tear over time.

Symptoms of a bad knob include: 

• loose, wobbly, or improperly functioning knobs
• fading or crackling of printed numbers/icons  
• missing screw caps or mounting hardware
• knobs that do not turn smoothly or snap fully into place

This Whirlpool replacement knob restores accuracy in the workflow. Compatible with legacy models, it ensures continued ease of use. This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Kenmore. 

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.

Color: metallic. Measures about 10 inches wide by 5 inches deep. Be sure to measure old filter before ordering. If your filter measures approx 11 1/4" x 6 1/8" use R0710163.

Replace a damaged or worn console with this control panel assembly. It restores a clean, secure mounting surface for the user controls and helps protect internal components so your appliance looks right and operates as intended.

• Houses and supports the user interface components (buttons/knobs/keypad and display bezel)
• Keeps controls aligned and securely mounted for proper operation
• Shields internal wiring and control electronics from incidental contact
• Helps resolve issues like loose controls, cracked or warped console fascia, and heavy cosmetic wear

• Disconnect power at the breaker or unplug the appliance before starting; shut off gas supply if applicable
• Remove any knobs/trim and the screws securing the old panel; support the panel while detaching
• Transfer required hardware, bezels, and brackets from the original panel to the new one
• Reassemble carefully and verify controls move freely before restoring power

Color: black. It measures about 2 inches in diameter.

This burner cap sits on top of the surface burner head to shape the flame and shield the head from spills. Replacing a damaged or missing cap helps restore even heating, reliable ignition, and the cooktop's original appearance.

• Covers the burner head and disperses flame for more even cooking
• Protects burner head and ports from food and liquid spills
• Helps maintain proper ignition and a steady blue flame
• Helps with symptoms like uneven/yellow flame, delayed ignition, or poor simmer

• Allow the cooktop to cool completely before handling
• Disconnect power and shut off gas
• Clean the burner head and clear ports before seating the cap
• Center the cap so it sits level and flush; misalignment can affect ignition and flame