Jenn-Air Cooktop Parts

I ordered the part I was sure I needed through the Appliance Pro website. I was surprised the part arrived in just two days. FIRST UNPLUG THE OVEN.. I removed the baking racks then two screws holding the plate over the element. I then removed three screws holding the old element in place, then gently wiggle/pull the element free from the electrical connections in the back of the oven. (Note: You cannot see the connections at this point. You'll need to remove the terminal block cover on the... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Ordered the replacement glass through AppliancePartsPros.com and it arrived the next day. Wow! There are three pieces of glass (four if you include the front glass panel on the oven door when it is closed) layered inside and in looking at the diagram I ordered #7 and #24 replacement parts. I figured while I was in there the oven glass looked stained and maybe I would want new glass. With that said when the glass arrived and my husband and I got the oven door off and apart, we realized I... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat
• Oven is too hot

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Took out the old element and checked with olm meter determined bad, no continuity. Orded new Element from Appliance Parts Pros. Had new one in less than 2 days easy fix. Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more