Jenn-Air Wall Oven Burner & Related Parts

This surface burner head distributes gas to the flame on a gas cooktop or range burner. Replacing a worn or clogged head helps restore even flame, reliable ignition, and consistent heat on the affected burner.

• Channels gas from the orifice through burner ports to create a uniform flame pattern under the cap
• Works with the spark electrode to ignite the gas
• A damaged or clogged head can cause: burner won't light or only clicks; uneven/yellow flame; weak or low heat on that burner
• Carbon buildup or corrosion on the head can lead to delayed ignition

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the burner cap; take off the old head and retain any mounting screws
• Align the new head over the orifice and spark electrode; seat flat and secure
• Clean burner ports and cap before testing for a steady, blue flame

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.

This burner head distributes gas evenly around the burner for a steady flame and reliable ignition. Replace a worn or clogged head to restore even heating, proper simmering, and consistent burner performance on your gas range or cooktop.

• Spreads gas from the orifice through ports to create an even, controlled flame ring
• Works with the burner cap and igniter/electrode for quick, consistent lighting
• Replace if ports are clogged, corroded, cracked, or warped causing uneven/yellow flames, delayed ignition, or popping
• Can help when the igniter sparks but the burner won't light or the flame won't spread

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the burner cap, then lift off the old head (some models use a retaining screw—reuse existing hardware)
• Align the new head with the orifice and igniter; seat fully and level
• Reassemble and test for proper ignition and flame; do not enlarge or clean ports with hard objects

This gas surface burner head sits on the burner base and channels gas through precision ports for quick ignition and an even flame. Replacing a worn or clogged head helps restore reliable lighting and consistent heat.

• Distributes gas from the burner base to the flame ports for even flame patterns
• Interfaces with the spark electrode to enable ignition
• Helps maintain proper flame shape and heat output
• Common symptoms include burner won't light, weak/uneven or yellow flames, delayed ignition, or continuous clicking

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift the old burner head off the base
• Clean the burner base and electrode area; align the new head with locator pins and the electrode opening, then seat fully
• Reinstall cap and grate; restore gas/power and test ignition and flame

This Orifice Spud precisely meters gas to a burner so you get a steady, properly sized flame. Replace a damaged, clogged, or incorrect spud to restore reliable ignition, clean flame color, and consistent heating.

• Threads into the burner's orifice holder/valve to control gas flow through a calibrated opening
• Helps maintain correct flame height and color for safe, efficient cooking
• Typical symptoms include irregular or yellow flames, weak or no flame, popping, or delayed ignition
• A clogged or worn spud can make simmer control difficult and lengthen cook times

• Shut off gas supply and power; allow the appliance to cool before service
• Remove grate, cap, and burner head (as applicable) to access the orifice; use the proper wrench or nut driver and avoid overtightening brass parts
• After reassembly, restore gas and check for leaks with soapy water; verify a steady blue flame and adjust air shutters only if directed by the manufacturer

This gas surface burner cap sits on top of the burner head to shape an even flame and shield the burner from spills. Replace a missing, chipped, or warped cap to restore proper flame pattern and appearance.

• Directs and evens the flame across the burner for consistent heating
• Shields the burner head and ports from spills and debris
• Helps promote reliable ignition when properly seated on the burner head
• Common signs it's needed: uneven or yellow flames, delayed ignition, flames lifting or noisy, visible chips/warping

• Ensure the cooktop/range is cool; disconnect power and shut off gas if working near igniters
• Lift off the old cap and clean the burner head/ports; do not enlarge or damage the ports
• Place the new cap on the matching burner, centered and seated flat; do not interchange sizes between burners
• Light the burner and confirm a steady, even blue flame; reseat the cap if the flame is uneven

Sealed burner assembly that supplies a protected gas flame for a gas range, restoring consistent heat and helping keep spills and debris out of the burner box. Designed as a direct-replacement assembly for affected burners. What it does

• Provides the sealed gas flame source used for cooking on a gas cooktop
• Restores even heat distribution when a burner is warped, damaged, or not producing a steady flame
• Helps prevent spills and food debris from entering the burner cavity, reducing corrosion and ignition problems
• Symptom linkage: commonly replaced for uneven heating, weak or irregular flame, visible burner damage, or excessive soot

• Includes 1 sealed burner assembly

• Turn off the gas supply and electricity to the appliance before starting any service
• Follow model-specific disassembly steps (lift or remove cooktop/grates as required); do not force fittings or gas connections
• If you smell gas, shut off the gas supply immediately

• WP3403M075-29 — confirm this matches your original part before ordering

This burner cap sits on top of the surface burner head to shape the flame and shield the head from spills. Replacing a damaged or missing cap helps restore even heating, reliable ignition, and the cooktop's original appearance.

• Covers the burner head and disperses flame for more even cooking
• Protects burner head and ports from food and liquid spills
• Helps maintain proper ignition and a steady blue flame
• Helps with symptoms like uneven/yellow flame, delayed ignition, or poor simmer

• Allow the cooktop to cool completely before handling
• Disconnect power and shut off gas
• Clean the burner head and clear ports before seating the cap
• Center the cap so it sits level and flush; misalignment can affect ignition and flame

This orifice spud is the small gas burner fitting that holds the burner orifice and helps direct fuel to the burner for proper ignition. It restores correct gas flow to the burner assembly for reliable ignition and flame. What it does:

• Secures the burner orifice in the burner tube so the correct-sized jet is positioned for ignition
• Helps maintain steady, consistent gas flow to the burner
• Commonly replaced when burners fail to light or flame is weak/irregular
• Works with the burner tube assembly to ensure proper burner operation

• One orifice spud

• Turn off gas supply and unplug appliance before beginning service
• Use correct tools and replace only the part(s) explicitly specified for your model
• Do not overtighten fittings; follow torque guidance from the appliance manufacturer
• If you smell gas or suspect a leak after installation, stop immediately

This orifice meters gas flow to a range or oven burner for consistent, controllable flames. Replacing a damaged or clogged orifice restores proper burner performance and helps maintain safe ignition and cooking. What it does

• Controls the gas flow to a specific burner for the correct flame size and heat output.
• Commonly replaces clogged, corroded, or damaged orifices that cause weak or uneven flames.
• Can resolve symptoms such as burners that won't light reliably, low flame, or irregular flame shape.
• Helps restore stable combustion when the flame is sputtering or lifting from the burner head.

• One gas burner orifice (single piece as shown)

• Turn off the appliance and shut off the gas supply before removing or installing the orifice.
• Use the correct-size wrench; avoid overtightening which can damage the fitting.
• Inspect threads and seat for debris; replace sealing gasket or use approved thread sealant per service manual if specified.

This natural gas burner orifice regulates gas flow to the cooktop burner for a consistent 17K output, restoring proper flame size and heat. It's a direct-fit replacement designed for compatible Whirlpool-range gas valves and burners. What it does

• Controls gas flow to the burner so the flame reaches the intended heat output
• Helps correct weak or uneven flames when the orifice is clogged or worn
• Can resolve ignition or simmering problems caused by improper gas flow
• Matches the OEM 17K specification for proper burner performance

• One natural gas burner orifice (17K)

• Turn off the gas supply and power to the appliance before servicing
• Remove burner components carefully to access the orifice; avoid forcing fittings
• After installation, check for leaks with a soap solution or approved gas leak tester

The Regulator is an OEM replacement part for Whirlpool gas ranges. It regulates the flow of gas from the supply line to the burners, ensuring safe and efficient operation of your range. It maintains a consistent gas pressure, allowing for accurate and controlled heat distribution during cooking.

A bad pressure regulator can occur due to wear and tear, clogging, or damage to the internal components. If you notice symptoms such as uneven flame, difficulty in igniting the burners, or gas leaks, it may be time to replace the pressure regulator.

Symptoms of a bad gas pressure regulator include:

• Uneven flame
• Difficulty in igniting burners
• Gas leaks

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This burner cap fits over a gas cooktop's surface burner to help direct flame for even heating and protect the burner head. It restores proper burner appearance and helps maintain efficient flame pattern for cooking. What it does:

• Covers and protects the gas burner head from spills and debris
• Shapes and stabilizes the burner flame for consistent heat distribution
• Helps prevent flame disturbance that can cause uneven cooking or clicking
• Restores a finished look to the cooktop surface

• 1 burner cap

• Turn off gas supply and ensure all surfaces are cool before handling
• Remove loose debris and set the cap on the burner head so it seats evenly
• If cap is warped or does not sit flat, inspect burner head for damage or debris
• Use only manufacturer-recommended parts and follow your appliance's service instructions

The Gas Range LP Conversion Kit is an OEM part for specific Whirlpool gas ranges. It allows built-in ranges fueled by natural gas to be safely converted for use with liquid propane (LP) fuel. 

Symptoms requiring an LP conversion would include: 

• Inability to ignite or achieve proper combustion using natural gas 
• Unstable burner flame patterns or inconsistent heat output
• Gas leaks or improper connection to an LP fuel supply

Causes for needing an LP conversion kit include choosing to install the range in an area only serviced by LP gas, rather than natural gas. Additional causes could be wear and failure of the original equipment over time.  

This OEM kit is compatible with select Maytag, KitchenAid, Jenn-Air, and Kenmore gas ranges.

The LP Conversion Kit is an OEM part for Whirlpool gas cooktops. This kit allows a range designed for natural gas to be safely converted for use with liquid propane gas.

The conversion kit includes all necessary components to modify the gas valve, burner heads, and airflow to accommodate propane fuel. This ensures proper gas-air mixture and optimal combustion when operating on liquid propane.

Causes of needing conversion include switching to propane fuel when the range was originally set up for natural gas.

Symptoms of needing an LP conversion include:

• Inability to ignite burners or oven pilot light on propane
• Yellow burner flames and decreased heat output
• Gas smell from the range

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.