Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Rear Drum Bearing Sleeve is an OEM part for GE dryers. It is designed to support the rear of the dryer drum, ensuring smooth rotation during the drying cycle. This sleeve reduces friction between the drum and the bearing, contributing to efficient and quiet operation of the dryer. This is the dryer rear drum bearing sleeve only. For the rear drum bearing kit order WE25M40.

You should replace the rear drum bearing sleeve if it becomes worn out or damaged. Causes of a bad bearing sleeve can include regular wear and tear, lack of lubrication, or excessive loads that cause undue stress on the component. A malfunctioning bearing sleeve can lead to increased friction, noise, and potential damage to other parts of the dryer.

Symptoms of a bad rear drum bearing sleeve include:

• Squeaking, grinding, or rumbling noises during the drying cycle
• The dryer drum not rotating smoothly or being off-balance
• Increased drying times due to inefficient drum movement
• Visible wear or damage to the sleeve

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Toe Panel Insulation is an OEM part for Whirlpool dishwashers. This part was designed to enhance the appliance's performance by reducing noise and preventing heat escape from the bottom of the dishwasher. This insulation panel fits snugly behind the dishwasher's toe panel, which is located at the lower front part of the unit. 

Causes of a bad Toe Panel Insulation might include wear and tear over time, damage during appliance installation or removal, or deterioration due to moisture exposure. 

Symptoms of inadequate or damaged Toe Panel Insulation include:

• Noticeable increase in noise level from the dishwasher, making it more disruptive during its operation.
• Excess heat felt near the base of the dishwasher, indicating heat loss.
• Potential for condensation or slight temperature changes in the kitchen due to the heat emitted from the dishwasher.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Glass Light Lens is an OEM part for GE microwaves. It covers the light bulb inside the microwave, protecting it from food splatters and ensuring even illumination.The lenses measure approximately 7" x 3".

Causes of a bad glass light lens can include accidental impact, exposure to high heat, or general wear and tear.

Symptoms of a bad glass light lens include:

• Cracks or breaks in the glass
• Diminished visibility inside the microwave
• Light not being properly diffused
• Potential exposure of the light bulb to food splatters

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Refrigerator Door Shelf Bin Assembly is designed to enhance the functionality of your Samsung refrigerator. This genuine OEM part ensures a perfect fit, providing additional storage space in the door compartment for your beverages, condiments, and other essentials. Made with durable materials, the assembly offers reliable performance and helps keep your items organized and easily accessible. By replacing a cracked or damaged shelf bin with this high-quality component, you can restore the efficiency of your refrigerator and maintain a tidy kitchen environment. The Refrigerator Door Shelf Bin Assembly is compatible with a range of Samsung refrigerator models, making installation straightforward and hassle-free. Investing in this genuine OEM part not only extends the life of your appliance but also enhances your overall user experience by optimizing storage and organization within your fridge.

The Stirrer Fan Cover is an OEM replacement part for GE Microwaves. It is responsible for shielding internal mechanisms during operation. 

Causes of a faulty cover include normal wear over time, cracking, or warping due to exposure to high heat. 

Symptoms of a problematic cover include:

• Excessive noise or vibration during use
• Reduced or uneven heating performance
• Gaps exposing vulnerable electrical components
• Loose pieces that could fall into the microwave cavity

This GE replacement part is also compatible with Hotpoint, RCA, and select Kenmore models.

The Canopy Mica is an OEM part for GE microwaves. This part covers the waveguide channel, preventing food particles and grease from entering the microwave's internal mechanisms.  

Causes of a bad canopy mica can include exposure to high levels of moisture or grease, physical damage such as cracks or burns, and general wear and tear over time.  

Symptoms of a bad canopy mica include:

• Sparks or arcing during microwave operation
• Burn marks or discoloration on the mica sheet
• Unusual noises while the microwave is running
• Uneven cooking or heating of food

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Wave Guide Cover is an OEM part for Frigidaire microwaves. The cover prevents food particles and moisture from entering the wave guide, helping to maintain the efficiency and safety of the microwave.

Causes of a bad wave guide cover can include exposure to high heat, splatters from food and liquids, or regular wear and tear. 

Symptoms of a bad wave guide cover include:

• Sparks or arcing inside the microwave
• Uneven cooking or heating
• Visible burns, cracks, or discoloration on the cover
• Noise or rattling sounds during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cover restores a clean, secure fit over an opening on your appliance, helping shield internal components from dust, moisture, and debris. Replace a damaged or missing cover to maintain proper protection and appearance. What it does:

• Shields internal parts from grease, dust, and debris intrusion
• Helps maintain proper airflow and component protection as designed
• Reduces vibration or rattling from loose or broken panels
• Restores a finished, factory look when the original is cracked or missing

• 1 cover

• Disconnect power to the appliance before servicing
• Note fastener locations and orientation for correct reinstallation
• Reuse original screws/clips unless your unit specifies otherwise
• Use gloves and caution—panel edges and surrounding metal can be sharp

The Microwave Cooktop Lamp Glass Cover is an essential replacement part designed to restore the functionality and appearance of your microwave. This genuine OEM part ensures a perfect fit and seamless integration with your Samsung microwave, maintaining the quality you expect. Crafted from durable glass, the cover provides reliable protection for the cooktop lamp, allowing for consistent and clear illumination during use. Easy to install, this glass cover helps enhance your cooking experience by ensuring proper lighting within your appliance. By choosing the Microwave Cooktop Lamp Glass Cover, you benefit from improved visibility and a maintained aesthetic, keeping your microwave looking and operating like new. Whether your original cover is cracked, damaged, or no longer functioning, this genuine OEM part offers a straightforward solution to extend the life of your microwave and ensure optimal performance.

The Microwave Oven Light Lens Cover is an OEM replacement part for GE microwaves. It serves as the protective glass shielding the internal light fixture. Reliable lens safety and clarity are pivotal to effortless visibility within microwave cavities.

Causes of a damaged light lens cover can include cracks or breaks from impact accidents during cleaning, warping from excessive heat exposure over time, or scratches obscuring transparency.

Symptoms of a compromised lens cover include:

• Cloudiness or opacity inhibiting light diffusion
• Exposure of live electrical wiring beneath broken glass
• Gaps permitting liquid/debris ingress into delicate internals
• Inability to accurately monitor microwaved items cooking

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the clear glass lens that covers the cooktop light on select GE over-the-range units. It shields the bulb from grease and splatters while allowing bright, even illumination of the cooking surface below.

• Protects the cooktop light bulb from grease, moisture, and debris
• Restores proper lighting if the original lens is missing, cracked, or stained
• Helps maintain safe, even illumination of the range area
• Common symptoms: broken or missing lens, dim or uneven light due to a damaged cover

• Disconnect power to the appliance before servicing
• Allow bulbs and surrounding area to cool completely
• Handle glass carefully to avoid chipping; wear cut-resistant gloves
• Ensure the lens seats fully and any retaining tabs/screws are secured per the product's service instructions

This factory shield is a protective panel used within the appliance assembly. It helps guard nearby components and maintain proper operation by directing heat, air, or moisture as designed. Replacing a damaged or missing shield restores correct fit and protection.

• Provides a protective barrier for internal components in the specified area
• Helps manage airflow/heat/moisture path as engineered for the system
• Replace if cracked, warped, missing, or not securing firmly
• Typical signs include visible damage, rubbing/rattling, or evidence of heat/moisture exposure near the shield

• Disconnect power; shut off gas/water if applicable before servicing
• Access the location per your model's service information
• Transfer and reuse original clips/fasteners as needed; do not overtighten
• Verify alignment and clearances before reassembly and testing

This molded resin cover is a protective plastic shield used inside the microwave. It helps protect internal components and ducting from splatter and debris and restores a secure, finished fit when the original cover is cracked or missing. What it does:

• Shields internal components from grease, steam, and food splatter inside the unit
• Helps maintain proper airflow paths and a snug, rattle-free fit
• Common replacement when the original cover is cracked, warped, loose, or missing
• Visual cue: exposed internal parts or a cover that won't stay secured

• One resin (plastic) cover

• Disconnect power (unplug or switch off the breaker) and allow the unit to cool
• Access the cover location; remove retaining screws/clips and keep hardware for reuse
• Align the new cover and secure it without overtightening
• Ensure the cover is fully seated and not contacting nearby moving parts before restoring power

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on