Kenmore / Sears Dishwasher Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

A shield switch that helps prevent oven/range operation when the door is open and ensures safe control behavior. Replaces a worn or failed interlock switch to restore normal start and door-safety responses. What it does:

• Acts as an interlock micro switch to detect door/cover position and block operation when open
• Commonly replaces a switch causing the control to not start or to behave intermittently
• Can resolve issues like no power to heating elements, control not responding, or oven not entering bake/lock modes
• Small electrical switch that completes or breaks the circuit based on door/cover position

• Disconnect power to the appliance before servicing to avoid shock or injury
• Replace the switch with the same part orientation and secure all connectors firmly
• Verify correct operation by restoring power and testing door open/close and normal cycle starts

This replacement capacitor shield protects the appliance's capacitor from debris, contact and shorting, helping extend component life and reduce electrical faults. It installs over the capacitor to block dust, wiring contact and accidental damage. What it does:

• Covers and protects the capacitor from physical contact, dust and loose wiring
• Helps prevent short circuits and arcing caused by accidental contact with the capacitor
• Useful when existing shield is cracked, missing or deformed
• Can reduce risk of intermittent electrical faults related to exposed capacitor

• One capacitor shield (protective cover)

• Always disconnect power to the appliance before servicing
• Capacitors can hold a charge; discharge safely before touching electrical components
• Remove necessary access panels to reach the capacitor; replace shield without stressing wires

This replacement shield is a small protective cover that helps guard nearby components from heat, moisture, or debris, reducing wear and preventing damage for reliable appliance operation. What it does:

• Covers and protects adjacent parts from heat, moisture, grease, or debris
• Helps maintain proper airflow or clearance around components where fitted
• Prevents rubbing, chafing, and minor impact damage to wiring or panels
• Can reduce noise caused by loose or exposed parts contacting other surfaces

• One replacement shield

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the shield
• Follow OEM disassembly steps for access; handle mounting tabs carefully to avoid breakage
• Use appropriate fasteners; replace any damaged clips or screws with OEM equivalents