Dishwasher Guard, Shield, Barrier Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Toe Panel Insulation is an OEM part for Whirlpool dishwashers. This part was designed to enhance the appliance's performance by reducing noise and preventing heat escape from the bottom of the dishwasher. This insulation panel fits snugly behind the dishwasher's toe panel, which is located at the lower front part of the unit. 

Causes of a bad Toe Panel Insulation might include wear and tear over time, damage during appliance installation or removal, or deterioration due to moisture exposure. 

Symptoms of inadequate or damaged Toe Panel Insulation include:

• Noticeable increase in noise level from the dishwasher, making it more disruptive during its operation.
• Excess heat felt near the base of the dishwasher, indicating heat loss.
• Potential for condensation or slight temperature changes in the kitchen due to the heat emitted from the dishwasher.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This replacement shield is a stamped metal protective panel that helps protect internal appliance components from heat, moisture and debris. Installing a good shield preserves surrounding parts and restores proper clearance and airflow. What it does

• Shields internal components from heat, splashes and grease to prevent premature wear
• Helps maintain proper airflow and component clearance inside the appliance
• Prevents debris and drips from reaching sensitive parts or wiring
• Replaces damaged, bent or corroded shields that can cause rubbing or noise

• One replacement shield

• Disconnect power (or unplug and shut off water for combinations) before starting any repair
• Wear gloves to protect hands from sharp edges; handle the part carefully
• Retain and reuse any mounting hardware unless replacement hardware is specified

This tub guard protects the washer tub rim and helps prevent clothes from catching or tearing at the top edge. It restores a smooth tub opening and reduces fabric wear for safer, quieter loads. What it does:

• Covers and smooths the exposed tub rim to stop fabric snags and tears
• Helps reduce noise and vibration caused by contact between clothing and the tub edge
• Maintains a finished appearance at the washer drum opening
• Works with the existing tub seal and trim to improve load handling

• One tub guard

• Disconnect power and turn off water before starting any repair
• Remove the washer agitator or top panel only if required for access; follow your model's service instructions
• Align the guard with the tub rim and press into place until it snaps or seats evenly; ensure the seal is continuous
• If any clips or screws are present, reinstall securely; discard damaged guards and replace with correct part

A shield switch that helps prevent oven/range operation when the door is open and ensures safe control behavior. Replaces a worn or failed interlock switch to restore normal start and door-safety responses. What it does:

• Acts as an interlock micro switch to detect door/cover position and block operation when open
• Commonly replaces a switch causing the control to not start or to behave intermittently
• Can resolve issues like no power to heating elements, control not responding, or oven not entering bake/lock modes
• Small electrical switch that completes or breaks the circuit based on door/cover position

• Disconnect power to the appliance before servicing to avoid shock or injury
• Replace the switch with the same part orientation and secure all connectors firmly
• Verify correct operation by restoring power and testing door open/close and normal cycle starts