Kenmore / Sears Freezer Parts

Directs water from valve to dispenser or ice maker in your freezer. Replace if cracked, kinked, or leaking. Restores proper water flow to internal system.

Access panel cover that protects internal components and provides a finished look. Replace if the original is cracked, broken, or missing from your appliance.

Replace your cracked, broken, or missing freezer storage basket. Restores organization and holds frozen items securely in the factory track system.

This breather valve regulates air pressure between the freezer compartment and the outside environment, allowing the door to open easily after the compressor cycles. It prevents a vacuum from forming inside the freezer as the air cools and contracts. Replace this valve if the freezer door is difficult to open shortly after closing or if you hear unusual hissing sounds from the freezer.

This is a white lid that fits on top of a chest-style refrigerator or freezer, providing access to the interior storage compartment. It seals the unit to maintain proper temperature and energy efficiency. Replace this lid if it is cracked, warped, or if the hinge mounting points are damaged, causing poor sealing and temperature fluctuations inside the unit.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Interior liner for freezer door that holds insulation and mounting points. Replace if cracked, dented, warped, or broken to restore door structure and finish.

Fixes frost buildup in freezer by controlling defrost cycles. This bi-metal sensor prevents overheating during defrost. Moderately easy repair.

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.

Door breaker trim kit with corner pieces for freezers. Installs along door edges to protect and seal. Replace if cracked, broken, or missing pieces.

Replacement cabinet corner trim for freezers. Restores the finished edge where the original trim piece has cracked, broken, or gone missing. Easy install.

Wire storage basket for upright freezers. Holds and organizes frozen food items. Replace if your original basket is bent, damaged, or missing.

Support spacer for refrigerators. Installs between components to maintain proper alignment and clearance. Replace if cracked, broken, or missing.

Replace a broken or missing shelf support peg in your freezer. This small plastic peg secures shelves and bins in place for stable storage organization.

Foam insulation sleeve that wraps around the defrost drain tube. Replace if worn, missing, or damaged to prevent condensation and maintain proper insulation.

This is a wire-style clamp that secures the overload relay cover on the compressor at the back of the refrigerator. It holds the protective cover tightly in place over the relay and overload components to prevent them from coming loose. Replace this clamp if it is bent, broken, or missing, which can allow the relay cover to detach and leave electrical components exposed.