Freezer Touch Pad

The Control Module is an OEM part for Frigidaire refrigerators. This electronic component manages and regulates the various functions of the refrigerator, including temperature control, defrost cycles, and the operation of fans and compressors.

You should replace the control module if it fails or malfunctions. Causes of a bad control module can include electrical surges, wear and tear over time, or exposure to moisture. Faulty wiring or damaged components within the module can also lead to failure.

Symptoms of a bad control module include:

• Inconsistent or incorrect temperatures in the refrigerator or freezer
• Refrigerator not cooling properly
• Frequent cycling on and off of the compressor
• Error codes displayed on the control panel

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Control Only - Touchpad and housing no longer included.

The User Control Board is an OEM part for Frigidaire upright freezers. As the central processing unit, this board regulates all electrical components including temperature controls, diagnostic systems, and interface buttons located on the outside of the freezer door.

Symptoms of a failing user control board include:

• Fluctuating or unresponsive temperature settings
• Inoperative display, lights or control buttons
• Error codes and diagnostic problems appearing

Causes can include normal wear from extended use. Exposure to temperature fluctuations inside the freezer can also deteriorate electronic connections over time.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Electrical Control is an OEM part compatible with Frigidaire upright freezers. As the primary processing board, it monitors all freezer functions including temperature, fans, lighting, and door sensors. A faulty control compromises dependability.

Symptoms of a bad control include:

• Inconsistent or fluctuating interior temperatures  
• Failure of lights or other electrical accessories
• Poor fan or defrost performance issues
• Error codes displayed on control panels

Causes can be water intrusion disrupting circuits, dust buildup over many years of operation, or typical wear over time.  

This Frigidaire OEM part fits Electrolux, Gibson, Danby and select Kenmore models for a factory-accurate replacement that preserves reliability.

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine OEM part is a control display unit for freezers. The control display unit is the part that houses the digital display and buttons for the freezer settings. It displays the temperature of the freezer. Over time, a control display can become damaged due to excessive wear and tear. If the screen is cracked or the buttons are no longer operating, then the control display unit will need to be replaced.To replace this part, start by unplugging the freezer. Once it has been powered off, proceed to pry the display unit out from the freezer using a flat head screwdriver or putty knife. Gently pull up until it is released from its mounting brackets. After removal, take the new unit and snap it into its brackets, making sure it is securely in place. Restore power to the appliance.This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand freezers.

The Freezer Control Board is an OEM part for Frigidaire freezers. It manages and regulates the various functions of the freezer, including temperature control, defrost cycles, and compressor operation. This control board ensures that the freezer maintains the correct temperature and operates efficiently.

Over time, the freezer control board can fail due to electrical surges, component wear, or manufacturing defects. When the control board malfunctions, it can disrupt the overall performance of your freezer, leading to inconsistent freezing and other operational issues.

Symptoms of a bad freezer control board include:

• The freezer not maintaining the correct temperature
• The freezer running continuously or not running at all
• Unresponsive control panel or error codes displayed
• Irregular defrost cycles causing ice buildup

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is the electronic control board that governs the appliance's cooling system. It interprets sensor input and user settings to run key components, helping maintain consistent temperatures when the original controller becomes faulty or erratic.

• Monitors temperature sensor feedback and executes cooling cycles to hold the selected setpoint
• Controls major components on applicable models
• May manage additional functions like defrost timing or alarms depending on model design
• Failure can present as warm or unstable temperatures, unit not starting, short-cycling/running constantly, or unresponsive temperature adjustments

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Note wire/plug locations; transfer connectors to the new board one at a time
• Secure the board in its mounting and ensure all harnesses are fully seated
• Reassemble covers/panels before restoring power and checking operation

The Main Control Board  is an OEM part for GE refrigerators. This main control board serves as the central control hub for your refrigerator, responsible for regulating various functions such as temperature control, defrost cycles, and overall operation.

A bad main control board can occur due to electrical issues, component failure, or other factors. If you notice symptoms such as erratic temperature readings, unresponsive controls, or complete refrigerator malfunction, it may be time to replace the main control board.

Symptoms of a bad main control board include:

• Erratic temperature readings
• Unresponsive controls
• Complete refrigerator malfunction

Restore proper function to your GE refrigerator by replacing the faulty main control board with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This electronic control board manages the appliance's core functions and user inputs so the unit can run cycles, regulate settings, and respond to commands reliably after the original board fails. What it does:

• Receives user inputs and runs timed/temperature/sequence commands for the appliance.
• Controls relays, displays, and sensors linked to normal operation.
• A failed board can prevent cycles from starting or cause unpredictable operation.

• Disconnect all power before servicing to avoid shock or damage.
• Handle the board by its edges and ground yourself to prevent static discharge.
• The connector layout must match your appliance before installation.

This electronic control is the oven's main user interface and control board, restoring reliable cycle selection and display feedback so your range or wall oven responds correctly and settings hold as expected. What it does:

• Interprets button/touchpad inputs and sends commands to heating elements, timers and relays.
• Restores or corrects digital display, clock and oven mode functions.
• Can resolve symptoms such as blank or erratic display, unresponsive controls, incorrect bake/clean cycles, or oven failing to start.
• Works as the central board that coordinates temperature and timing signals for normal oven operation.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing controls.
• Handle the board carefully to avoid static discharge; avoid touching circuit traces or components.
• Follow the appliance's service manual or diagram for correct wire connections and panel reassembly.

This is the electronic temperature control board for select refrigerators/freezers with EZ Set controls. It regulates interior temperature based on sensor feedback and user settings to keep food safely stored.

• Monitors temperature sensor(s) and cycles compressor/defrost as designed
• Interfaces with EZ Set user controls to adjust cooling level
• Faulty boards can cause warm or too-cold temperatures, erratic cycling, or unresponsive controls
• May resolve intermittent cooling or control panel issues when properly diagnosed

• Unplug the appliance before servicing; use ESD protection when handling electronics
• Access location varies by model; note all wire connections before removal
• Handle connectors and board carefully; avoid bending pins or stressing harnesses
• After installation, restore power and allow 24 hours for temperatures to stabilize

Restore accurate cooling and responsive controls with this Electronic Control Board. It monitors sensors and user settings to manage your freezer's key operations so the unit reaches and maintains the temperature you choose.

• Regulates cooling by commanding the compressor and evaporator fan to maintain set temperature
• Interprets thermistor and keypad inputs to execute temperature changes
• Coordinates defrost timing and temperature alarm functions on applicable models
• Symptoms it may address: not cooling or overcooling, runs constantly or won't run, erratic/inaccurate temperature display, beeping alarm, unresponsive buttons or display

• Disconnect power before servicing; handle the board by its edges and use ESD protection
• Note/photograph wiring before removal; transfer any reusable mounting brackets or covers
• Ensure all connectors are fully seated and locked
• After installation, set your desired temperature and allow up to 24 hours for temperatures to stabilize

This part is a control board that is manufactured for use on freezers. This component manages the functions of the freezer, including the temperature settings and the defrost cycle time. It features a digital display and well as buttons to control each setting.When the control board only works intermittently, it is time to replace it before it completely stops working. The display may stop working or will blink on and off. The replacement process is very easy and only takes about 5 minutes to complete. It simply snaps in and out. The person performing the repair may find a wide putty knife handy to push in the two clips on each side. Unplug the freezer before replacing this part.This particular control board is compatible with freezers that are manufactured by Frigidaire, Kenmore, and Electrolux. It is sold individually. This part is sourced straight from the manufacturer as a genuine OEM replacement part.

Control panel overlay that replaces worn, faded, or damaged printed labels on the console. Restores readable button markings and a factory look while protecting the underlying control surface from everyday wear. What it does:

• Replaces the printed graphic layer on the console so buttons and settings are easy to read.
• Protects the control surface from scratches, spills and wear.
• Helps resolve symptoms like faded or peeling labels and unclear button legends.
• Maintains the original appearance and layout of the control area.

• Disconnect power (unplug or switch off breaker) before servicing the appliance.
• Remove the console or trim carefully to avoid damaging switches, clips or wiring; adhesive may need to be softened or cleaned.
• Handle the overlay by the edges to avoid fingerprints on the printed surface; use appropriate cleaners and let adhesives fully set before reuse.

This HMI assembly is the freezer control/display interface that lets you view and set freezer temperature and use front-panel functions. Replacing a faulty HMI restores normal display and button response for freezer controls. What it does:

• Provides the user interface (display, touchpad/buttons) for the freezer control functions
• Sends user commands to the refrigerator control system so temperature and modes can be changed
• Commonly fails when the display is blank, unresponsive, or buttons don't register
• Can cause intermittent or incorrect freezer readouts and control behavior when damaged

• Disconnect power to the appliance before beginning any work
• Handle the assembly and ribbon/connectors carefully to avoid damage
• Reconnect all plugs firmly and verify operation before reassembling trim and panels

This electronic control board replaces the refrigerator's main control module to restore reliable control of temperature, defrost, and compressor cycles. It fixes intermittent or non-responsive controls for better cooling performance and consistent operation. What it does:

• Receives user inputs and manages compressor, fans, and defrost timing to maintain set temperatures
• Controls display and status indicators so settings and alarms register correctly
• Stops erratic cycling and resolves symptoms like no cooling, unresponsive buttons, or blinking lights
• Helps correct error codes caused by failed or intermittent control signals

• One electronic control board (main control)

• Disconnect power to the appliance before starting work to avoid electrical shock
• Handle the board carefully; avoid touching contacts and use proper ESD precautions when possible
• Compare part number on the old board to ensure correct replacement before installing