Kenmore / Sears Microwave Screws, Nuts, Washers

Secure hex bolt for microwave assembly. Replaces lost, stripped, or damaged mounting bolts. Essential hardware for panel attachment and stability.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Replacement screw that secures panels, trim pieces, and mounting brackets on cooktops and ranges. Needed when screws are missing, stripped, or damaged.

Factory mounting screw secures panels, brackets, and internal components in microwaves. Replace missing, stripped, or corroded screws to keep assemblies tight.

Flat-head 10-32 zinc screw secures panels and components on cooktops, ranges, and ovens. Replace stripped, missing, or corroded screws for proper fit.

Truss-head self-tapping screw for securing microwave panels, trim, and brackets. Replace lost or damaged mounting screws to restore fit.

Replacement mounting screw for microwave panels and components. Secures brackets, vents, and assemblies. Needed when original fastener is missing or damaged.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

Replacement mounting screw secures exterior panels, trim, or internal components. Needed when original fastener is missing, stripped, or damaged.

Toggle nut for microwave installation and mounting. Replaces missing, stripped, or damaged nuts. Essential hardware for secure panel attachment.

Washered screw secures panels, brackets, and internal microwave components. Replace if screw is missing, stripped, or damaged to restore proper fit.

A flat washer used with the appliance's fastening hardware to distribute load and reduce wear. Helps maintain secure connections and prevents damage to mating surfaces for reliable operation. What it does:

• Provides an even bearing surface for bolts or screws to prevent pull-through
• Reduces friction and wear between fasteners and housing parts
• Helps keep fasteners tight and resists loosening from vibration
• Commonly used where a smooth, protective spacer is needed

• Verify correct location and orientation before reassembly
• Use manufacturer-recommended fasteners and torque specifications
• Power off and unplug the appliance before accessing internal components

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Mounting screw for microwave installation and panel assembly. Replace if stripped, missing, or damaged during maintenance. Essential hardware component.

This 4.0x16mm tapping screw secures trim, panels, and brackets on ranges and microwaves. Replace missing, stripped, or damaged screws during repair.