Kenmore / Sears Range / Cooktop / Oven Valve

This top burner valve controls gas flow to a single cooktop burner so you can adjust heat and restore proper burner operation. It replaces a worn or failed valve to help burners light and hold a steady flame. What it does:

• Regulates gas flow from the manifold to one surface burner for precise heat control.
• Replaces valves that are stuck, hard to turn, or fail to deliver consistent flame.
• Helps resolve symptoms like a burner that won't light, weak or uneven flame, or loss of ignition control.
• Works as a direct replacement when the original valve is damaged or leaking.

• One top burner gas valve.

• Turn off gas supply and electrical power to the appliance before starting work.
• Only install on compatible gas ranges; follow OEM instructions and local codes.
• Use proper fittings and sealants rated for gas; check all connections for leaks after installation.

This top burner gas valve controls gas flow to a single cooktop burner, restoring proper flame control and allowing safe ignition and adjustment. It's designed as a direct replacement part for compatible gas ranges. What it does:

• Regulates gas to one top/burner for steady flame control
• Helps resolve symptoms like burner failing to light, weak or inconsistent flame, or inability to adjust flame level
• Works with the burner orifice and valve stem assembly to modulate gas flow
• Intended for use only on compatible range models and configurations

• Turn off gas supply and disconnect power before servicing
• Use proper fittings and torque; inspect connections and test for leaks with a gas leak solution after installation

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring proper water delivery and ice production when the valve is functioning. It replaces a failed or leaking valve to stop water loss and restore operation. What it does

• Directs and regulates incoming household water to the ice maker and dispenser.
• Stops water flow when the refrigerator is off or valves are closed to prevent leaks.
• Commonly linked to symptoms such as no water to the dispenser, slow water flow, or no ice production.
• Can cause leaking or pooling under the refrigerator when the valve body or fittings fail.

• One new water inlet valve assembly.

• Disconnect power and shut off the water supply before beginning any repair.
• Expect to access the valve behind the lower access panel or at the rear of the refrigerator.
• Tighten supply line fittings securely and check for leaks after reinstalling and turning the water back on.

A replacement safety valve kit that restores a safety shutoff component to appliances, helping stop flow when a fault is detected so the unit can operate safely. Fits compatible Frigidaire appliances that use this OEM kit. What it does

• Replaces the appliance's safety valve assembly to restore proper shutoff function
• Prevents continued fuel or water flow when a fault or unsafe condition occurs
• Commonly used when the appliance fails to start, fails to heat, or shows safety-related shutdowns
• Helps resolve intermittent operation or safety trip symptoms tied to a failed valve

• One safety valve kit (single complete replacement kit)

• Disconnect power and gas/water supply before starting any repair
• Follow the appliance's service manual or wiring diagram for correct routing and connections
• Use proper tools and safety gear;
• Test for leaks and proper operation after installation and before returning the appliance to service

This replacement valve and screw assembly controls the flow at the appliance connection and restores proper operation of the related water or fluid path. It's a direct-fit service piece that replaces a worn or damaged valve assembly. What it does

• Acts as the valve element that opens and closes to allow controlled flow through the service line.
• Common symptom: reduced or no flow where the valve is used.
• Common symptom: visible leaks or dripping at the valve connection.
• Helps stop intermittent flow issues caused by a damaged valve or mounting screw.

• Disconnect power and shut off the water (or related supply) before starting work.
• Use basic hand tools; avoid overtightening the screw to prevent damage.
• Inspect nearby seals and tubing for wear and replace if needed.

This water inlet valve controls water flow to the refrigerator's dispenser and ice-making system, restoring proper water delivery when the factory valve fails. Designed as a direct-replacement valve assembly for compatible Frigidaire units. What it does

• Opens and closes to allow water into the ice maker and door dispenser when signaled
• Prevents water flow when the dispenser or ice maker is inactive
• Common symptom: dispenser or ice maker does not dispense water or fills slowly
• Common symptom: water intermittently flows or the ice maker fails to fill

• Disconnect power and shut off the water supply before beginning work
• Drain remaining water from lines to limit spills during removal
• Replace mounting hardware and tubing fittings exactly as removed; use plumber's tape where appropriate on threaded connections
• Inspect connections and test for leaks after restoring power and water