Kenmore / Sears Range Hood Parts

The range hood speed control wire harness is the set of wires that connects the fan speed switch to the hood's motor, transmitting the signals that control airflow levels. It ensures your hood fan operates correctly at each selected speed setting. Replace this part if your range hood fan only runs at one speed, won't turn on at certain settings, or if you notice burnt or damaged wiring.

This is a plastic retainer clip that holds the grease or charcoal filter in place inside a range hood. It snaps into the hood housing and keeps the filter securely mounted during operation. Replace this part if your filter is loose, rattling, or falling out of position.

This rotating component is mounted on the motor shaft inside the range hood and moves air through the ventilation system. Replace when the hood produces reduced airflow, makes excessive noise, or fails to clear cooking smoke and odors effectively.

Carbon filter for range hoods and over-the-range microwaves. Dimensions: 4-7/8" x 27" x 3/8" (4.875 x 27 x 0.375). Rectangle shape. Removes cooking odors from cooking air. Replace when clogged, discolored, or every 6-12 months.

Rubber bushing that reduces vibration and noise in range hood assemblies. Replace if worn, cracked, or missing to restore quiet operation and stability.

Fix unresponsive buttons, lights that won't turn on, or a fan that won't run. This range hood control board manages fan speed, lighting, and user controls.

Fix a weak, noisy, or non-working range hood fan with this blower motor. Restores proper ventilation and airflow when the fan won't spin or runs poorly.

Replace your cracked or damaged range hood cover housing. This exterior panel protects internal components and restores the finished appearance of your unit.

Blower housing scroll that channels airflow inside the ventilation assembly. Replace if cracked, broken, or missing to restore proper air direction.

This is a vent damper designed for use with a range hood exhaust system. It mounts in the ductwork and uses a gravity or spring-loaded flap to allow air to flow out while preventing outside air, drafts, and pests from entering when the hood is off. Replace this part if you notice cold drafts coming through the hood vent, the damper flap is stuck, or the existing damper no longer seals properly.

This is an electrical wire lead used to restore or replace a damaged connection in the appliance. It provides a direct conductive path so motors, lights, or controls can receive power and signals reliably. What it does:

• Reconnects power or signal between components when the original wire is damaged or broken
• Restores functionality for motors, fans, lights, or switches that are losing power due to a faulty lead
• Prevents intermittent operation caused by frayed, corroded, or cut wiring
• Helps maintain safe electrical continuity when properly installed and secured

• One wire lead

• Disconnect mains power before inspecting or replacing wiring to avoid shock or injury
• Match wire color, connector type, and routing to the original; use proper crimps/terminals or solder and insulated sleeving
• Secure wire away from moving parts and heat sources; replace any damaged insulation or clips

Replace your range hood light lens cover to protect bulbs from grease and restore even lighting. Snaps into place in under a minute. Confirm fit by model.

Grease filter for range hoods and over-the-range microwaves. Dimensions: 9-7/8" x 11-11/16" x 3/8" (9.875 x 11.6875 x 0.375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Range hood fan stopped working or runs weak? This motor assembly restores proper ventilation. Most DIYers complete installation in 5-20 minutes.

Grease filter for range hoods and over-the-range microwaves. Dimensions: 8-3/4" x 10-1/2" x 3/32" (8.75 x 10.5 x 0.09375). Basket shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Replacement control knob for range hood light or fan speed settings. Installs on control shaft. Needed when original knob is cracked, broken, or missing.