Kirkland Parts

The Deflector is an OEM replacement part for Whirlpool dishwashers. Located in the lower corners of the tub, this component works to prevent leaks by keeping water from entering the cracks along the tub edges.

Causes of a bad corner deflector can include cracks, chips, or breaks from repeated impact or stress over time. Mineral buildup can also cause deflectors to warp or become misshapen, reducing their effectiveness.

Symptoms of a bad corner deflector include:

• Water leaks or moisture inside the cabinet below the dishwasher
• Puddles or drips near tub corners after cycles
• Mineral residue or pooling in lower tub corners

Replacing the corner deflector with a new OEM part restores a tight seal to prevent water from entering cracks and causing leaks or damaged components inside the cabinet.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Approx. 11" H x 14" W x 17" Deep.

The Bimetal Defrost Thermostat is an OEM part for Whirlpool refrigerators. This thermostat plays a key role in the defrost system, helping to regulate the temperature within the freezer to prevent frost buildup on the evaporator coils. By activating the defrost heater, it ensures the coils remain ice-free and the refrigerator operates efficiently. The thermostat operates within a range of 20F (closing temperature) to 50F (opening temperature).

Causes of a bad defrost thermostat can include electrical faults, exposure to constant temperature fluctuations, or wear and tear over time. When the thermostat fails, it can result in frost accumulation, impacting the cooling efficiency.

Symptoms of a bad bimetal defrost thermostat include:

• Frost buildup in the freezer
• The refrigerator running continuously or not cycling properly
• Inconsistent freezer temperatures
• Water leaks inside the refrigerator

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rinse Aid Cap is an OEM part for Whirlpool dishwashers. It is designed to securely cover the rinse aid dispenser, ensuring the proper release of rinse aid during the wash cycle to improve drying performance and prevent water spots on dishes.

Causes of a bad rinse aid cap can include wear and tear over time, damage from accidental mishandling, or loss of the cap. Without a properly functioning cap, the rinse aid may not dispense correctly.

Symptoms of a bad rinse aid cap include:

• Rinse aid leaking or not dispensing
• Water spots or streaks on dishes after drying
• The cap not fitting securely or being visibly damaged
• The rinse aid compartment remaining full or not using rinse aid as expected

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Defrost Control Board is an OEM part for Whirlpool refrigerators. This board manages the defrost cycle by controlling the defrost heater and monitoring the freezer's temperature. 

Causes of a bad defrost control board can include electrical issues, wear from continuous use, or damage from power surges.  

Symptoms of a bad defrost control board include:

• Excessive frost buildup in the freezer compartment
• The refrigerator not cooling properly
• The defrost heater not activating
• The refrigerator running continuously without cycling off

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement dishrack restores secure loading and proper spacing so wash water reaches every item. Replacing a bent or rusty rack helps prevent tipped dishes and marks from flaking rust, and keeps loading/unloading smooth when the rack rollers are intact.

• Holds plates, bowls, and cups in place during wash and rinse cycles
• Maintains spacing for spray coverage and drying airflow
• Rolls in and out along the rails when paired with functional rack rollers
• Common symptoms include broken or bent tines, flaking coating or rust, items tipping, or difficulty sliding the rack

• Disconnect power to the dishwasher before servicing
• Open the door, pull the rack forward, release rack stops/end caps if present, and slide the old rack off the rails
• Transfer any reusable accessories from the old rack to the new rack as required by your model
• Slide the new rack onto the rails, reinstall rack stops, and verify smooth travel before running a cycle

This dishwasher silverware basket fits in the lower rack to hold and organize utensils during the wash. Replace a cracked, warped, or missing basket to keep flatware upright and prevent pieces from slipping through or rattling loose.

• Holds forks, knives, and spoons securely in the lower rack throughout the cycle
• Helps separate utensils for better spray coverage
• Direct replacement when the original basket is cracked, warped, or missing
• Common symptoms: utensils tip over or fall through, basket won't sit flat, plastic is broken or deteriorated

• No tools required; lift out the old basket and set the new one in the lower rack
• Ensure the basket sits flat and does not interfere with the lower spray arm
• Follow your dishwasher's loading guidance for utensil orientation
• Handle cracked plastic carefully and wear gloves if needed

This base heater assembly restores the oven's lower heating function in select convection microwaves. It delivers bottom radiant heat for baking and crisping so the unit can preheat properly and brown foods evenly.

• Supplies bottom heat during convection, bake, or crisp cycles
• Works with the control and temperature sensor to reach and maintain set temperature
• Common symptoms of a failed heater may include no heat in convection mode, very long preheat, or poor browning/crisping
• Visible damage to the element or tripping a circuit breaker may also indicate a shorted heater

• Disconnect power before servicing. Microwaves contain high-voltage components that can retain a charge even when unplugged
• Allow the unit to cool completely; access typically requires removing the outer cover or lowering an over-the-range unit
• Note wire locations and routing before removal; transfer any brackets, shields, or screws from the original assembly
• Route wires exactly as original and avoid pinching; confirm clearances before reassembly and test a convection preheat

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

The Hinge Pin is an OEM part for Whirlpool refrigerators. This part allows the door to open and close smoothly, providing a durable pivot point for the door's movement.

Over time, hinge pins can wear down or become damaged due to the constant stress of door movement, improper alignment, or accidental force applied to the door. A compromised hinge pin can lead to issues such as difficulty in opening or closing the door, a door that hangs unevenly or doesn't seal properly, and increased wear on other door components.

Symptoms of a bad Hinge Pin include:

• Squeaking or resistance when opening or closing the door
• The door not closing fully or sealing properly
• Visible wear or damage to the pin
• The refrigerator or freezer door hanging unevenly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This replacement door spring maintains proper tension so the door opens smoothly and doesn't drop. Replace a weakened or broken spring to restore controlled, balanced door movement and everyday usability. What it does:

• Provides tension to balance the door's weight during opening and closing
• Helps prevent the door from slamming open or falling unexpectedly
• Common fix for a door that feels heavy, drops open quickly, or won't hold a mid-position
• Replaces springs that are stretched, fatigued, or broken

• 1 door spring

• Disconnect power before servicing; springs are under tension—use gloves and eye protection
• Note the spring's routing and hook positions; take a photo before removal
• Use pliers to release and attach the spring carefully to avoid sudden release
• Some models use two springs; replace both for even tension if applicable

This mechanical thermostat monitors temperature and opens or closes the circuit at a fixed set point to control heat and prevent overheating. Replacing a failed thermostat restores safe operation and consistent performance. What it does:

• Senses surface or component temperature and switches the circuit at a calibrated threshold
• Helps protect heaters, motors, and controls from thermal damage due to over-temperature
• Common symptoms of failure: no heat, shuts off mid-cycle, won't start until cooled, or intermittent operation
• Restores proper temperature control after a thermostat sticks open/closed or drifts out of spec

• 1 thermostat

• Disconnect power at the breaker (and shut off gas, if applicable) before servicing
• Note wire positions and transfer leads one-for-one to the new thermostat
• Mount flush against the sensing surface with original screws/clips; reinstall any insulation or thermal interface material as found
• Correct the root cause (blocked vents, failed fan, restricted airflow, or buildup) before returning the appliance to service

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.

This is the center hinge for the refrigerator doors. It supports and aligns the doors at the midpoint so they open smoothly and seal properly, helping maintain temperatures and reliable day-to-day operation.

• Provides the middle pivot point between the upper and lower doors
• Keeps door alignment and spacing correct for a tight gasket seal
• Common symptoms: door sagging or rubbing, squeaking/grinding, door not closing or popping open, uneven gaps
• Replace if the hinge bracket or pin is bent, worn, or corroded

• Disconnect power and clear items from the doors before starting
• Support the doors; a second person is recommended when removing hinge screws
• Note the order of any shims/spacers or washers and transfer them to the new hinge
• After installation, align doors and verify full gasket contact all around