Kitchenaid Dishrack

This genuine replacement part is an upper dishrack. The upper dishrack is the top shelf of a dishwasher that holds plates, bowls, and utensils. Over time through continuous use, this upper rack may become damaged, making it difficult to secure dishes during a wash cycle. If the dishrack is visibly damaged or no longer opening and shutting properly, it will need to be replaced. Thankfully, replacing this dishrack is a relatively simple process.To remove the old dishrack, simply pull it out and lift the wheels from its track. Set it off the side, and lift the new dishrack. Slide it into its track and make sure it is locked in. If it is gliding in and out smoothly, it has been installed properly.This genuine replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This genuine OEM adjuster helps set and fine-tune an appliance's alignment so doors close correctly and the cabinet sits level. It restores stable operation and reduces rocking or vibration caused by an uneven appliance surface. What it does:

• Provides a threaded adjustment point to raise, lower, or support an appliance corner or panel
• Helps correct uneven cabinets, tilted doors, or appliances that rock or vibrate during use
• Restores proper door alignment and sealing when misalignment is caused by height/level issues
• Works as the appliance's mechanical support where an adjustable foot or bracket is used

• Always disconnect power (and water, if applicable) before servicing the appliance
• Support the appliance securely before making height adjustments or removing/installing the adjuster
• Use appropriate hand tools; avoid excessive force that could damage threads or mounting points

This positioner aligns and secures its mating component in the correct location inside your appliance. Replacing a cracked, worn, or missing positioner restores proper fit so the assembly stays put and operates as designed.

• Holds the related part in the proper position and orientation
• Prevents shifting, sagging, or rattling during use
• Supports smooth adjustment or movement where applicable
• Common symptoms: loose or misaligned component, difficulty adjusting or seating the piece, visible cracks, or a missing clip

• Disconnect power; also shut off gas or water if your appliance uses these utilities
• Note the original orientation and take photos before removal
• Transfer any reused hardware and fully seat tabs/slots to avoid damage
• Wear cut-resistant gloves and check alignment after reassembly

This cover is a factory replacement access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded from dust and accidental contact for safer, longer-lasting operation. What it does:

• Shields internal wiring, controls, and components from dust, debris and accidental contact
• Keeps small parts and fasteners secured inside the appliance cabinet
• Restores the appliance's finished exterior where the original cover was damaged or missing
• Helps maintain proper airflow routing and component spacing when installed correctly

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Verify the cover orientation and fastener locations before securing; use OEM screws where specified.
• Handle with care to avoid scratching or bending the cover; ensure tabs snap fully into place.
• Inspect for damage and secure any loose parts before installing the cover.

The Tine Clip is an OEM part specifically designed for Whirlpool brand dishwashers. This small but important piece secures individual tines to the upper dish rack for stability during washing.

Repeated use causes plastic clips to become brittle or dislodge over time from heavy loads. This jeopardizes proper rack assembly and performance. 

Causes of a bad tine clip could be normal wear and tear, damaged pads from sharp dishes, or improper loading of heavily soiled cookware.

Symptoms of a failing tine clip include:

• Loosened or detaching dishrack tines that shift positions 
• Gaps allowing collected food and particles to fall through
• Reduced support for delicate or small dishes in affected areas

This OEM Whirlpool replacement restores the rack's fully functional design. Compatible with Maytag, KitchenAid, Jenn-Air, and other models, it improves washing coverage and optimizes usable space.
 

This replacement door handle restores a secure grip and smooth opening for compatible Whirlpool appliances. It replaces worn, cracked or broken handles to improve usability and appearance without replacing the whole door. What it does

• Provides a sturdy handhold to open and close the appliance door
• Replaces cracked, loose or cosmetically damaged handles
• Helps prevent accidental drops or slippage when opening the door
• Matches the original mounting points for a direct-fit replacement

• Remove power and empty the door area before starting any repairs
• Use common hand tools; hold parts steady to avoid scratching finishes
• Follow OEM instructions for fastener torque and alignment

This small retaining clip secures trim, panels, or components in place to prevent rattling or detachment during normal operation. It's a simple, low-profile fastener that restores fit and function where the original clip has broken or gone missing. What it does:

• Holds panels, bezels, or wiring harnesses in position to stop vibration and movement
• Replaces worn, broken or missing clips that cause loose trim or gaps
• Helps maintain proper alignment of adjacent parts for reliable operation
• Works as a direct-fit fastening solution where the original clip is used

• One retaining clip

• Disconnect power to the appliance before attempting any repair
• Access may require removing panels or trim; use appropriate screwdrivers or trim tools
• Install by aligning the clip with the mating slot or hole and pressing firmly until it snaps into place

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Track is an OEM part for Whirlpool dishwashers. It serves as the track or rail that allows the dishrack to glide smoothly in and out of the dishwasher during loading and unloading. The track is precision-engineered to provide smooth, controlled movement of the dishrack. It includes all necessary mounting brackets and attachments to facilitate simple installation.

Causes of a bad track can include scratches, dents or other damage due to impact or repeated use over time. The roller or wheel components may also become worn down or jammed, hindering proper movement.

Symptoms of a bad track include:

• The dishrack not rolling out fully or getting stuck partway
• Scratching or scraping noises when moving the dishrack
• Difficulty pushing the dishrack in and out
• The dishrack tilting or becoming unbalanced during movement

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: There are four wheel assemblies includes with this rack. The flexible tine rows are not included. This is a lower dishrack assembly for a dishwasher. This part holds the dishes during the washing and drying cycles. Note that this is only the lower dishrack assembly and the upper dishrack assembly is sold separately. Over time, the lower dishrack assembly may begin to rust or the coating may wear off. It is also possible that sections of the part could break due to degradation over time. If this happens, the entire lower dishrack assembly will need to be replaced. The lower dishrack assembly is compatible with dishwashers that are manufactured by the Kenmore, KitchenAid, and Whirlpool brands. It comes straight from the manufacturer and is sold individually. It's a genuine, high-quality, and durable OEM part.

This replacement lower dishrack restores the main loading surface in your dishwasher so dishes sit securely and spray reaches them for better cleaning. It replaces a cracked, rusted, or misshapen rack to help protect dishes and keep loading organized. What it does

• Provides a stable platform to hold plates, bowls and cookware during wash cycles
• Maintains correct spacing so spray arms can reach all items for effective cleaning
• Replaces bent or rusted rack wires that can snag or chip dishes
• Helps keep utensil baskets and rollers aligned for smooth rack movement

• One lower dishrack

• Remove dishwasher racks and disconnect water/electric only if required by your model; most rack swaps are simple hand installs
• Inspect and transfer any rollers, clips, or utensil baskets from the old rack to the new one if needed
• Handle carefully to avoid wire ends that may be sharp; wear gloves if helpful
• If rails or rollers are damaged, replace those parts as well for proper rack operation

Color: white. It measures about 1-1/2 inches high by 2 inches deep.