Kitchenaid Range / Cooktop / Oven Heating Element

Burner not heating or 'Hot Surface' light stays on? This electric cooktop surface element is likely the fix. DIY-friendly, most installs take 15 minutes.

Oven not heating or preheating slowly? This lower bake element restores even baking when burned out or damaged. DIY-friendly, 5-minute install.

This 8-inch surface coil element restores a burned-out or damaged heating element on an electric cooktop. It delivers consistent 2100W heat for everyday boiling, frying, and simmering, so your range burners perform like new.

• Provides direct, even heat for pots and pans on coil-top ranges
• Common symptoms: surface element won't heat, heats unevenly, or cycles off prematurely
• Visual signs can include blisters, breaks, or hot spots on the coil
• Helps resolve issues caused by a failed element rather than the switch or receptacle

• Unplug range or switch off circuit breaker before servicing
• Allow the old element to cool completely before handling
• Pull the element straight out from the receptacle; align and push the new one fully into place
• Inspect the element receptacle for heat damage and replace if needed for best results

Burner won't heat or stuck on high? This surface element restores proper heating control to your electric range stovetop. Common DIY repair.

If your cooktop burner won't heat or stays on high, this surface heating element may need replacement. Moderate DIY repair with basic tools.

This is a flat electric heating element designed to power the built-in griddle on a range cooktop. It provides even heat across the griddle surface for cooking. Replace this element if your griddle no longer heats, heats unevenly, or shows visible damage such as cracks or burn marks.

This boiler is the dishwasher water-heating assembly that provides the hot wash and rinse temperatures needed for effective cleaning. Replaces a failed boiler to restore normal heating during dishwasher cycles. What it does:

• Heats water used during wash and rinse cycles so detergent can clean effectively
• Helps maintain proper cycle temperatures for sanitizing performance
• Stops working when the element fails or the boiler leaks or overheats
• Often linked to no-heat cycles, prolonged wash times, or error codes related to water temperature

• Disconnect power and water supply before starting any repairs
• Inspect for leaks and damaged connectors; replace any worn mounting hardware or seals
• Handle electrical connections carefully and follow the appliance's service manual for wiring and testing

If your wall oven won't heat, heats unevenly, or takes too long to preheat, the bake element may have failed. This lower heating element is essential for consistent baking.

This is a convection heating element for an oven, typically a circular or loop-shaped element located at the rear wall of the oven cavity near the convection fan. It provides even heat distribution when using the convection cooking mode. Replace this element if convection baking produces uneven results, the element shows visible damage or burn-through spots, or the convection mode fails to heat at all.

Oven not heating or baking unevenly? This range bake element restores proper heating. Common DIY repair that takes about 30 minutes with basic tools.

Oven not heating or baking unevenly? A failed bake or broil element is often the cause. This heating element restores proper oven temperature control.

Broil element not heating? This upper heating element fixes ovens that won't broil or bake properly. Most DIYers complete this repair in 15 minutes.

This is a circular heating element located at the rear wall of the oven cavity that works with the convection fan to circulate hot air for even cooking. It provides the heat source specifically for convection baking and roasting modes. Replace this element if convection cooking is uneven, the oven fails to reach proper temperature in convection mode, or if the element shows visible damage such as blistering or breaks.

This is an electric warming element used in a range or oven. It provides low, consistent heat to keep food warm after cooking without continuing to cook it further. Replace this element if your warming feature no longer heats, heats unevenly, or shows visible damage such as cracks or burn spots.

Oven not heating or baking unevenly? This bake element restores consistent heat for proper cooking. Common DIY repair, typically takes 30 minutes.