Kitchenaid Wall Oven Hinge Parts

Right side hinge receiver for door hinge. For left side hinge receiver use WP4455605.

This Door Hinge supports and pivots the appliance door for smooth operation and a square, reliable close. Replacing a worn hinge restores alignment so the door seals properly and opens and closes without binding or noise. What it does

• Supports door weight and provides the pivot point for opening and closing
• Maintains proper door alignment to help ensure an even gasket seal
• Restores smooth, consistent door movement
• Common symptoms: door droops or rubs, squeaks/grinds, or won't close flush

• Includes 1 door hinge

• Disconnect power before servicing
• Support the door and use a helper; remove contents as needed to reduce weight
• Mark hinge position and transfer any spacers/bushings in the same order
• Tighten mounting fasteners, then check alignment and gasket contact; adjust as needed

Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.

This right-hand oven door hinge assembly supports and counterbalances the door so it opens smoothly and closes firmly against the gasket. Replacing a worn hinge restores proper alignment and heat retention for consistent cooking performance.

• Provides the pivot point and spring tension for the oven door
• Helps the door open smoothly and close completely for a tight seal
• Wear or damage can cause sagging, misalignment, or slamming/falling open
• Heat loss from a poor seal may lead to long preheat or temperature fluctuations

• Disconnect power and allow the oven to cool completely before servicing
• The hinge is spring-loaded—support the door and use care to avoid injury
• Remove the door per your model's instructions, then replace the right-side hinge
• After installation, adjust per service guidance if needed

This oven door hinge restores smooth, controlled door movement and a tight seal. Replace a worn hinge to help your oven close properly, retain heat, and operate safely without slamming, sagging, or uneven gaps.

• Supports and pivots the oven door; spring tension controls opening and closing
• Helps the door sit flush against the gasket to minimize heat loss
• Restores alignment when the door feels loose, sags, or doesn't close evenly
• Resolves symptoms like door slamming, uneven gaps, poor temperature regulation, or extended preheat times

• Disconnect power at the breaker; shut off gas supply if applicable
• Support the door; engage hinge locks and remove the door
• Replace the hinge and securely reinstall using existing fasteners
• Rehang the door, verify latch engagement and seal, and test door movement

This replacement door hinge restores smooth, stable door movement and proper alignment. Replacing a worn hinge helps the door open and close correctly so the appliance seals as designed and operates safely.

• Provides the pivot point for opening and closing the door
• Helps maintain door alignment for a consistent, reliable seal
• Replaces a bent, loose, or worn hinge that affects door operation
• Common symptoms: door sags, won't close fully, pops open, binds, or squeaks

• Disconnect power; turn off gas or water supply before servicing
• Support the door during removal and installation to prevent damage or injury
• Compare the new hinge to the original and transfer any reusable hardware
• After installation, check door alignment and closure; adjust per your model's service instructions

For Stainless Models.

Right-side door hinge in white for refrigerator doors. Replaces a worn, cracked or damaged hinge to restore smooth opening and correct door alignment, helping reduce door sag and improve sealing. What it does:

• Provides the pivot and support for the refrigerator door on the right-hand side.
• Restores proper door alignment to help the gasket seal evenly and reduce cooling loss.
• Eliminates or reduces door sagging, binding, or noisy operation caused by a damaged hinge.
• Matches white exterior finish for a discreet repair.

• Unplug the appliance or disconnect power before beginning any repair.
• Support the door securely (use a helper or a prop) before removing the hinge to prevent injury or damage.
• Use the correct hand tools; align the door and tighten fasteners snugly but avoid overtightening.

This door hinge restores smooth pivoting and reliable alignment for a Whirlpool appliance door, helping the door close and seal properly. Replace a worn or damaged hinge to reduce sagging, rubbing, and uneven gaps. What it does:

• Provides a secure pivot point so the appliance door opens and closes smoothly.
• Restores proper door alignment to improve sealing and reduce cold loss or heat entry.
• Reduces rubbing, scraping noises, and binding caused by a bent or worn hinge.
• Commonly used when the door sags, sticks, or shows visible hinge damage.

• Disconnect power (and water, if applicable) and remove food from the appliance before starting.
• Support the door while removing/installing the hinge to prevent dropping or misalignment.
• Use the correct fasteners and tighten per OEM guidance; avoid over-tightening.

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly