Lg Range Parts

Note: Due to factory variations, please check your original board before ordering. This display control board has 17 buttons on the front. If your original board has 18 buttons, you may need part# EBR89296404 instead.

The Display PCB Assembly is an OEM part for LG ranges and stoves. It is the main circuit board that controls the display panel and oven. This assembly is responsible for operating all electronic functions such as temperature controls, timers, buttons and digital displays.

Causes of a bad display PCB assembly can be water or liquid damage, failure due to surges or spikes in the power supply over time, or due to normal component degradation after heavy use.

Symptoms of a bad display PCB assembly include:

• Faulty or unresponsive control buttons
• Erratic temperature control functions
• Glitches or failures in the digital display
• Inability to operate certain cooking modes

This OEM LG part is also compatible with some Kenmore models.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

Seals around your range door to maintain stable interior temperatures and reduce energy loss. Replace when worn, cracked, or no longer sealing properly.

Replacement mounting nut for cooktops and ranges. Secures components during installation. Order a new nut if yours is stripped, missing, or damaged.

Mounting screw for range installation and assembly. Secures components and panels. Order a replacement if your screw is stripped, missing, or damaged.

This 4.0x16mm tapping screw secures trim, panels, and brackets on ranges and microwaves. Replace missing, stripped, or damaged screws during repair.

Replacement mounting screw for electric and gas ranges. Secures components and panels. Needed when original screw is stripped, missing, or damaged.

Rubber bumper grommet for electric and gas ranges. Replaces cracked, worn, or missing grommets that cushion and support range components.

Support plate for range installations. Replaces broken, cracked, or missing mounting plates. Provides structural stability for secure appliance positioning.

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

Burner orifice holder for gas ranges. Holds the orifice that controls gas flow to burners. Replace if cracked, damaged, or when converting between fuel types.

This water inlet valve controls the flow of water to the refrigerator's dispenser and ice maker, restoring proper water delivery for ice production and dispensing. It's a direct-fit replacement that helps stop leaks and restore normal water flow. What it does

• Opens and closes to allow water into the ice maker and dispenser when called by the refrigerator's control system
• Commonly replaces valves that are leaking, stuck closed, or failing to supply water
• Helps correct symptoms like no ice production, weak/slow water dispensing, or visible leaks at the valve area
• Works with the fridge's water line and solenoid system to regulate water delivery

• One water inlet valve assembly

• Disconnect power and shut off the house water supply before starting any repair
• Only install if you can access the valve and water line connections; use proper tools to avoid damaging fittings
• Inspect and replace any worn inlet hoses or seals while accessible to prevent future leaks

Connects the broiler burner tube to the gas supply line in your range. Replace if cracked, corroded, or leaking to ensure proper gas flow to the broiler.