Lg Washer Dryer Combo Clip Or Clamp

The Outer Door Gasket Clamp is an OEM part for LG washing machines. It is designed to secure the outer door gasket, ensuring a tight seal between the door and the drum. This helps prevent water leaks during the wash cycle and maintains the efficiency of the washing machine.

Causes of a bad outer door gasket clamp can include regular wear and tear, damage from heavy use, or corrosion over time. A compromised clamp can lead to a loose gasket, resulting in water leaks and reduced washing machine performance.

Symptoms of a bad Outer Door Gasket Clamp include:

• Water leaking from the door area during wash cycles
• A loose or misaligned door gasket
• Difficulty in securing the door properly
• Visible rust or damage on the clamp

This OEM LG part is also compatible with Sears/Kenmore.

The Inner Door Gasket Clamp is an OEM part for LG washing machines. It secures the inner door gasket in place, ensuring a tight seal to prevent water leaks during the wash cycle. This clamp is essential for maintaining the efficiency and reliability of the washing machine by keeping the door gasket firmly in position.

Over time, wear and tear, exposure to water and detergent, or accidental mishandling can compromise the integrity of the clamp, leading to potential leaks.

Symptoms of a bad inner door gasket clamp include:

• Water leaking from the door area
• The door gasket not staying securely in place
•  Visible damage or corrosion on the clamp

This OEM LG part is also compatible with Sears/Kenmore.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

This clamp secures flexible hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal on water and drain lines. What it does:

• Holds a hose firmly to a barb or nipple to prevent slipping and leaks
• Helps stop common symptoms like dripping, visible leaks, or a loose hose connection
• Keeps hoses from shifting or vibrating during operation
• Works wherever a small metal hose clamp is used on plumbing or drainage connections

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide the clamp over the hose, seat the hose on the fitting, then tighten or crimp per the clamp type
• Use pliers or the correct tool for the clamp to avoid damage to the hose or clamp
• Replace with the same clamp style and size for a proper fit; inspect hose and fitting for wear

This replacement clamp secures flexible hoses and tubing to fittings to help prevent leaks and keep connections stable. It's a small but essential part for reliable water and drain line performance. What it does:

• Holds hoses or tubes firmly to barbs, fittings, or posts to prevent disconnection
• Helps reduce leaks and water seepage at hose connections
• Minimizes rattling or vibration from loose tubing
• Supports proper routing of lines to avoid kinks or wear

• Disconnect power and water supply before starting any repair
• Use appropriate hand tools (pliers or a screwdriver, depending on clamp type) and avoid over-tightening
• Inspect nearby hoses and fittings for wear and replace if damaged