Lg Clip Or Clamp

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should... Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more

The old filter head was broken at the supply line side connector fell out. The clicking noise eventually caused the fridge to warm up and stop cooling. The clicking was the overload relay tripping. The Start solenoid on the compressor was an Embarco TSD part 513604044. APP does not have that part nor does any else found a similar one on ebay but I ordered the PTC assembly 6749C-0014E. I removed the overload relay and capacitor from the TSD used two pieces of wire and connectors to create the... Read more

Took the door off by following an LG video which took about 10 minutes. I replaced the center hinge and put the door back on. Read more

I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more

I was kind of guessing at the parts that I needed, but the parts diagrams were a huge help, and I narrowed it down to the bushing and stopper on the right door. I removed the door and was able to replace the parts pretty easily. Now the fridge door works good as new. Read more

I went to your web site found the part using the model number of the washer machine. Also with the part picture, there was a video showing step by step instructions. They were very clear and was breeze replacing the hose.Doing this myself saved at least probably $150-200. Appliance repair shops quoted me around $80.00 just to come out. Then they mark up the price of the hose at least twice the cost of what I paid , They too have to order the part and come back to install. So the labor was what... Read more

Replaced tubing and fitting Read more

Replaced the motor. Read more

Ordered replacement assembly. Part ended up in middle of state before finally arriving at my home. Hardest part of repair was to remove food and refrigerator to do the work. I had watched videos which were pretty horrible. I was able to make it very simple by shutting off water, draining line and disconnecting everything in back. Then removed assembly and pulled out of refrigerator. The replacement part was easy to put in just be careful of the hook area, slide easy no force or you may break a... Read more