Parts for Ge CFE29TSDDSS: Machine Compartment Parts

Removes contaminants from your refrigerator's water and ice. Replace every 6 months or when the filter indicator activates. Confirm fit with your model.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Dishwasher not powering on or experiencing electrical issues? This terminal block housing insulator protects wire connections. Simple repair part.

This push-in fastener secures trim, panels, and plastic components on compatible appliances to prevent rattling and hold parts in place. Simple clip design keeps panels aligned without screws or specialized hardware. What it does

• Holds plastic trim, interior panels, and lightweight assemblies in place
• Replaces worn or broken push retainers that cause loose or vibrating panels
• Helps restore proper fit of door liners, kick plates, and interior housings
• Commonly used where a snap-in plastic retainer is required

• Push into the matching hole until the head seats flush; no tools typically required
• Inspect mating hole and surrounding material for damage before installation
• Remove power and follow appliance safety instructions when working near electrical components
• If fastener does not seat correctly, confirm correct part and hole size before forcing

Water leaking from connections? This locking clip secures 1/4-inch tubing in push-to-connect fittings on refrigerator water and ice systems.

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

Rubber grommet that cushions and protects refrigerant or water tubing where it passes through sheet metal. Replace if cracked, worn, or missing.

If your refrigerator is vibrating excessively or making rattling noises, the compressor mounting grommet may be worn. This rubber isolator reduces noise.

This compressor mounting stud secures the compressor to the refrigerator chassis, keeping the unit stable and reducing vibration and noise. It's a durable replacement part for worn, bent, or missing compressor mounting hardware. What it does:

• Provides a secure attachment point between the compressor and cabinet/frame
• Helps reduce compressor vibration and operational noise when correctly installed
• Prevents compressor movement that can stress refrigerant lines or electrical connections
• Commonly replaced when the original stud is corroded, damaged, or missing

• Disconnect power to the appliance before beginning any repair.
• Support the compressor while removing/installing mounting hardware to avoid strain on lines and fittings.
• Replace any associated nuts, washers, or insulators if worn or damaged; use correct hardware orientation.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

No water from dispenser or ice maker? The water inlet valve controls water flow to both. DIY-friendly repair takes about 2 minutes with basic tools.

Fridge completely dead with no lights or display? Main control board manages temperature, defrost cycles, and fan operation. Most DIYers complete in 10 min.

Replace a cracked or missing control board cover to protect electronics from moisture and dust. Simple snap-on installation takes 10-15 minutes.

This condenser support is the replacement mounting bracket that holds the refrigerator condenser or condenser coil securely in place, helping maintain proper clearance and airflow for reliable cooling performance. What it does:

• Secures the condenser or condenser coil to the cabinet to prevent movement or vibration
• Maintains correct condenser positioning to support consistent airflow and heat dissipation
• Helps reduce rattling or noise caused by a loose condenser assembly
• Supports overall cooling reliability by keeping components aligned

• One condenser support bracket

• Installation requires basic hand tools; disconnect power before beginning any repair
• Handle sharp sheet-metal edges carefully to avoid cuts
• Reinstall any removed panels or fasteners to restore proper airflow paths

Refrigerator not cooling properly? A failed condenser fan motor prevents heat dissipation. Most DIYers replace this in under 30 minutes with basic tools.

Roller wheel for bottom-mount refrigerators. Mounts to the base to allow smooth rolling movement. Replace if cracked, broken, or causing uneven gliding.

Fix refrigerator cooling issues or unusual noises with this jumper discharge wire. Compatible with French door and side-by-side models. Easy install.

This clamp tube secures small appliance tubing and lines to the cabinet, keeping water and refrigerant hoses routed and held in place to prevent chafing or pinch-related leaks. Durable plastic construction fits designated mounting points. What it does:

• Holds water, drain or refrigerant tubing against the appliance frame to prevent movement
• Helps reduce rubbing and chafing that can lead to leaks or hose wear
• Keeps lines organized for reliable operation and easier service access
• Works at common tubing attachment locations such as cabinet walls and brackets

• One clamp tube (single piece as shown)

• Remove power and water supply to the appliance before servicing
• Fastens into a molded or screw-type mounting boss; inspect mating surface for damage
• Replace only with the same style clamp to ensure proper fit and secure routing
• If tubing is damaged, replace the tubing as well—clamp only secures, it does not repair leaks

Fix a refrigerator that won't cool or runs constantly with this variable speed compressor kit. Restores efficient, quiet cooling and temperature control.

Fix your refrigerator not cooling or running constantly with this condenser fan plenum assembly. Connects airflow from fan to condenser coils.

Fix a refrigerator that won't cool properly or runs constantly with this condenser coil assembly. Restores heat dissipation and cooling efficiency.

Filter drier for refrigerator sealed systems. Removes moisture and contaminants from refrigerant. Replace if frozen, iced over, cracked, or restricted.

Leaking water at the back of your fridge? A failed valve body disrupts water flow to the dispenser and ice maker. Professional repair recommended.

Leaking water at the back of your fridge? A failed valve body disrupts water flow to the dispenser and ice maker. Professional repair recommended.

This pad mastic is an adhesive sealant used to secure foam pads and insulation inside the appliance, helping keep components in place and reducing vibration and air gaps for more consistent performance. What it does:

• Bonds foam pads, insulation and other non-structural components to appliance cabinet surfaces
• Helps reduce vibration and noise by holding pads firmly in place
• Seals small gaps to limit air movement and moisture around insulation
• Commonly used during panel, liner, or insulation repairs and reassembly

• Unplug the appliance or shut off power before starting any repair
• Clean and dry mounting surfaces; remove old adhesive and debris for best adhesion
• Press pad into place and hold as needed; allow adhesive to set per OEM recommendations
• Wear gloves and avoid skin/eye contact; ventilate area when working with adhesives

Reduces refrigerator vibration noise by damping component and panel contact. Replace deteriorated mastic to eliminate rattles and buzzing. Confirm fit.

Refrigerator won't power on or loses power intermittently? This power cord harness restores a secure electrical connection from wall outlet to appliance.

Water leaking under your refrigerator? A clogged or cracked drain tube and valve causes leaks and ice buildup. Easy DIY fix—simply pull off and push on.

Water leaking under your refrigerator? A clogged or cracked drain tube and valve causes leaks and ice buildup. Easy DIY fix—simply pull off and push on.

Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.

Secures panels, brackets, and internal components in refrigerators. Replace if screw is missing, stripped, or corroded. 1/4-20 thread, 7/8" length.