Parts for Ge GDE25EGKARBB: Machine Compartment Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.

Secures wiring harnesses and cables inside your refrigerator. Replace if broken, cracked, or missing to prevent wire damage. Verify fit with your model.

Mounting standoff spacer secures internal components, panels, and circuit boards inside your refrigerator. Replace if cracked, broken, or missing.

Seals icemaker water supply tubes and prevents air leaks in your refrigerator. Replace if you notice frost buildup, water leaks, or ice production issues. Verify fit with your model number before ordering.

Cardboard or metal cover that closes the machine compartment opening on your refrigerator back panel. Replace if cracked, missing, or water-damaged.

Fix electrical failures in your refrigerator's lower cabinet with this wiring harness. Connects components for proper operation. Moderate DIY repair.

Fix a refrigerator that won't cool or runs constantly with this compressor kit. Essential for restoring proper cooling in refrigerators and freezers.

The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator

Fix a refrigerator that won't cool properly with a new condenser assembly. This component releases heat to keep your fridge running efficiently.

Secures panels and trim pieces inside your refrigerator. Replaces broken or missing retainers that cause loose trim, rattling, or misaligned components.

If your refrigerator runs but doesn't cool or fails to start, the compressor start device may have failed. This relay and overload combo helps restore cooling.

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises fro

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the syst

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Plastic cover that conceals and protects water supply tubing behind the lower kickplate. Replace if cracked, broken, or missing for a finished look.

Fix no water to ice maker or dispenser issues with this refrigerator water inlet valve and guard assembly. Controls water flow to both systems.

Refrigerator not cooling or fans not running? The main control board manages temperature, defrost cycles, and compressor operation. Test thermistors first.

This sound damper cushions the refrigerator compressor to reduce vibration and minimize noise for quieter operation. It helps protect the compressor from metal-on-metal contact and dampens normal operating sounds. What it does:

• Cushions compressor mounting to absorb vibration and reduce noise
• Prevents metal-on-metal contact that can cause rattling or buzzing
• Helps stabilize the compressor to reduce wear from vibration
• Commonly used when compressor noise, rattling, or increased vibration is noticed

• One sound damper

• Always disconnect power to the appliance before beginning any repair
• Access the compressor area (rear lower cabinet); remove any panels as needed
• Remove the old damper and press the replacement onto the compressor mounting foot until fully seated
• If mounting hardware is damaged or the compressor mount appears worn, replace mounting parts.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

Hex washer head screw for securing refrigerator components. Replace if screw is stripped, missing, or damaged during maintenance or repair work.

Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.

Refrigerator running hot or not cooling properly? This condenser fan and housing assembly circulates air over condenser coils to dissipate heat and restore efficient cooling.