Parts for Kenmore 110.6814751 (1106814751, 110 6814751): Machine Sub-Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Filters debris from water entering your washer and seals the hose connection. Replace if water fills slowly or screens are clogged. Confirm fit by model.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.

Replace your washer's 5/16-18 hex nut if the original is stripped, missing, or corroded. Secures components during assembly and maintenance.

Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Shaft Seal is an OEM part for Whirlpool washing machines. This seal is designed to fit around the shaft that connects the tub to the transmission or motor, preventing water from leaking out of the tub and into the machine's internal components.

Causes of damage to the Shaft Seal often involve normal wear and tear from regular use, as the constant motion of the shaft can gradually degrade the seal.

Symptoms of a bad Shaft Seal include:

• Water leaking from the underside of the washing machine, particularly during or after a wash cycle
• A noisy operation, especially during the spin cycle, can sometimes result from water leaking into the bearings and causing them to fail
• The presence of rust or corrosion around the area where the shaft enters the tub

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.

This part has been discontinued by the manufacturer and is no longer available.

Fix a washer that won't drain or spin with this drain pump. Common repair for water remaining in tub after cycle. Moderate DIY repair effort.

This item has been dicontinued

Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.

Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.

• Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
• Helps prevent fasteners from loosening due to vibration and thermal cycling
• Common fix for rattling/vibration noises and components that work loose over time
• Replaces damaged, rounded, or missing original nut to restore proper fit

• Disconnect power and shut off gas/water supplies before servicing
• Remove the worn nut with the appropriate wrench or socket
• Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
• Inspect the mating bolt/stud and any washers; replace if worn or damaged

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

A replacement machine screw with 8-32 threads used to secure panels and components on compatible Whirlpool appliances. Installs quickly to restore proper fit and stop rattling or loose parts. What it does:

• Secures panels, trim, brackets or components that use 8-32 machine-thread fasteners
• Restores proper alignment and prevents vibration-related noise
• Replaces missing, stripped, or damaged screws that allow parts to come loose
• Works where a standard 8-32 machine screw is specified by the manufacturer

• Disconnect power and/or gas before servicing the appliance to reduce shock or injury risk
• Use the proper screwdriver or nut driver for the screw head to avoid stripping
• Thread gently and stop when snug; do not overtighten to prevent stripping or damage
• If threads are damaged, replace with the correct-size screw rather than forcing it

Seals the center post/agitator shaft to prevent water leaks during wash cycles. Replace if you notice pooling water under your washer. Confirm fit with your model.

The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.

Symptoms of a failing top lock may include:

• Inability to fully close or properly latch the dryer door
• Accidental opening from deficient locking during operation  
• Difficulty manipulating the lock due to worn or broken parts

Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

Includes 4 rubber washers, 4 metal washers, and 4 screws.

Small metal spacer washer that distributes load and maintains alignment in washer assemblies. Replace when worn, missing, or damaged to restore secure fit.

Noisy spin cycle or loose tub? This spanner nut secures the washer tub to the drive shaft. Requires spanner wrench for installation. DIY-friendly.

Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.