Need Help?
Call or text
Pilot burner assembly for gas range surface burners. Provides continuous flame for ignition. Replace when pilot won't stay lit, flame is weak, or assembly is damaged.
Replaced pilot and thermocouple. ..pilot flame was weak ...wasn't heating thermocouple enough to power the valve Read more
Replacement hinge for range oven doors. Sold individually; doors use two hinges. Replace if door won't stay closed, drops too fast, or is misaligned.
I had to take out the bottom drawer that holds pans. Disconnect the power and pull the oven out. Removed door, rear panel that held the screws for the side panel and lift up and out the side panel. After that it was straight forward as to replacing the hinge. Spent more time cleaning the florr where the oven was than installing the hinge. Read more
Color: black. It measures about 2 inches in diameter.
I searched the web for Appliance parts and found a place that had parts for my stove. I was hoping to have the part by a certain date stated 8/11 but didn't get it till 8/13 Read more
White burner control knob for electric ranges. Replace if your stovetop knob is cracked, broken, worn, loose, or missing. Installs on the control panel.
Determined that the LF infinite control switch contacts for the burner indicator light were stuck closed. I replaced the control as well as the knob as the knob felt loose on the control. Read more
Burner won't heat or heats unevenly? This 8-inch coil surface element restores reliable cooking power to your range. Simple plug-in installation.
It's one of the easiest jobs in the world. It take longer to unwrap the parts than to install them. Looks great...works great. Easy, Done. Read more
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat. Read more
This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.
I REPLACED THE HINGE ASSY ONLY BECAUSE I WAS UNABLE TO PURCHASE THE SPRING ONLY. THIS IS 3rd TIME I REPLACED THE HINGES BECAUSE OF A BROKEN SPRING. IT WOULD BE CHEAPER IF ONLY THE SPRING COULD BE BOUGHT. Read more
Replaces a broken or worn oven door hinge that no longer supports the door properly. Restores spring-loaded pivot action for smooth opening and closing.
Replaced the hinge Read more
Burner not heating or heating intermittently? This 8-inch surface element restores your cooktop. Easy DIY repair—just unplug the old, plug in the new.
Customer service went above and beyond to help me order the right parts. The parts came within 36 hours. We removed the heating elements and drip pans and replaced each as instructed in the videos on AppliancePartsPros.com . The whole process was seamless. Read more
Oven won't turn off or stays on low heat? This temperature-sensing thermostat regulates oven heat and prevents overheating. Moderate DIY repair.
I replaced the thermostat and its control switch as it was not able to turn off. Read more
Replace a broken or fatigued oven door spring to restore proper counterbalance. Installs behind side panel. Ensures door closes firmly and seals correctly.
It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more
Color: black. Measures about 2 inches in diameter.
Replaced burner tubes and installed a new nob on the sparker control. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.
First check to see how many leads your switch has before ordering - I ordered before I took things apart, and got an incorrect 2 lead version when I needed a 3. On starting the repair, at first thought I might have to take apart console - but happily, no. After turning off power, just carefully pried the old switch out (putty knife to depress plastic clips above & below), pulled out gently (not much slack on wires) and removed the old wires by gently easing them off the broken switch with a... Read more
Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.
Discover that drawer glide and one of the oven front legs were broken, found the parts at ApliancePartsPros and got my range as good as new now! Read more
Safety bracket that secures your range to the floor to prevent tipping. Replace if missing, broken, or during new installation. Essential for homes with children.
Installed it according to video watched. Read more