Magic Chef Refrigerator Parts

This thermostat regulates oven temperature to maintain consistent cooking heat. It replaces a failed temperature control that causes incorrect baking or uneven cooking. What it does:

• Senses oven temperature and signals the heating system to turn on or off
• Helps restore accurate temperature control when the oven runs too hot or too cold
• Commonly used when oven cycles irregularly or displays temperature-related cooking problems
• Works as the control sensor for maintaining set cooking temperatures

• One thermostat assembly

• Turn power to the appliance off at the breaker before starting work
• Mounting and connector locations vary by model; verify fit before final installation

This is a replacement control knob for the freezer temperature control shaft. It restores a secure grip and clear detent positions so you can set the freezer temperature easily. What it does:

• Replaces a cracked, worn or missing freezer temperature control knob
• Provides a firm grip and visible setting position for accurate adjustment
• Allows the control shaft to turn and stay at selected settings
• Helps resolve symptoms like a loose, spinning or non-engaging knob

• Disconnect power to the appliance before attempting replacement
• Pull the old knob straight off the control shaft; align and push the new knob fully onto the shaft until it seats
• If resistance is felt, stop and inspect the shaft and knob for debris or damage before forcing
• If the control shaft is damaged or the knob does not secure properly, replace the control.

This funnel directs water into the ice maker fill cup to ensure proper filling and reduce spills. It helps maintain reliable ice production by guiding water flow to the correct inlet area. What it does:

• Directs incoming water into the ice maker's fill cup so the correct amount reaches the ice mold
• Reduces splashing and overflow during the fill cycle
• Helps prevent water from pooling inside the freezer compartment near the ice maker
• Supports consistent ice production when installed and aligned properly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove the ice maker or access panel as needed to reach the old funnel
• Align the replacement funnel with the mounting tabs and secure per OEM orientation; avoid forcing it into place
• Test fill cycle after installation and check for leaks; for detailed steps

This replacement door handle restores a secure, comfortable grip for opening and closing your refrigerator or freezer door. It replaces a cracked, broken, or loose handle to improve safety and daily use. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles that can catch or pinch
• Helps prevent further damage to door trim from continued use of a damaged handle
• Restores normal operation and appearance to the appliance front

• Disconnect power to the appliance or unplug before starting any work to avoid injury
• Remove any food and clear workspace around the door for easier access
• Minor disassembly of the door trim or end cap may be required; retain all fasteners
• Follow the manufacturer's instructions for correct torque and alignment

A PTC starter that helps engage a compressor's start winding for reliable motor startup and shorter run-up. Use this direct-replacement thermistor when the compressor struggles to start or only hums instead of running. What it does:

• Provides a timed reduction in start-circuit resistance so the compressor motor can start smoothly.
• Helps prevent continuous start winding current after the compressor runs, protecting the motor.
• Common symptom fixes: compressor hums, won't start, or system cycles without cooling.
• Works as the electrical start device used in many refrigeration and small motor applications.

• One PTC starter (single thermistor start device).

• Disconnect all power before attempting replacement; risk of shock or equipment damage.
• Match the starter to the original part and wiring; replace only with the correct part number.
• Handle terminals carefully; do not short or bend leads.
• This is a non-serviceable component — replace rather than attempt repairs.

This motor overload protector helps prevent the dryer motor from overheating by cutting power when excessive current or heat is detected. It restores normal operation when the motor cools or the overload is replaced. What it does:

• Protects the dryer motor from damage by interrupting power during overheating or overcurrent conditions
• Commonly used when the dryer motor won't start, hums but doesn't run, or the motor trips repeatedly
• Works with the motor start system to reduce the risk of burned windings and costly motor failure
• Resets or is replaced to restore normal motor operation after an overload event

• Always unplug the appliance before checking or replacing this part
• Inspect wiring and motor for underlying issues that can cause repeated overloads

This is a flat plain washer used to distribute load and space hardware on appliance assemblies. It helps keep bolts and screws seated and reduces wear on mating surfaces for more secure fastener connections. What it does:

• Provides a flat bearing surface to spread clamp load and protect parts from fastener damage
• Maintains proper spacing and alignment for mounted components
• Helps prevent fastener loosening from vibration when used with the correct bolt or screw
• Commonly used on chassis, suspension, and bracket connections

• One plain flat washer

• Disconnect power and water supply before servicing the appliance
• Replace only with the same washer size and thickness as the original for proper fit
• Tighten fasteners to secure but avoid over-torquing which can deform the washer

This motor overload protector helps stop the motor when it overheats, protecting the appliance from damage and preventing unsafe operation. It's a small, replaceable safety device commonly used on motors and compressors. What it does:

• Interrupts motor power if the motor draws excessive current or overheats
• Helps prevent motor burnout and potential electrical hazards
• Can cause a no-start or humming motor when the protector has failed
• May reset automatically or require replacement depending on design

• Disconnect power before accessing or replacing the part
• Handle terminals carefully and match wiring/terminal placement exactly
• Use only the specified replacement part; do not bypass or modify the protector

A small replacement screw used to secure appliance panels and components so assemblies stay aligned and stable during normal use. Simple, direct fix for loose trim, panels, or mounting points. What it does:

• Secures panels, brackets, or small components to prevent rattling and movement
• Restores proper alignment where a missing or damaged fastener causes gaps
• Helps stop vibration-related noise from loose parts
• Functions as the original-style fastener matching OEM fit and purpose

• Disconnect power and water to the appliance before servicing where applicable
• Use the correct screwdriver or bit to avoid stripping the head
• Thread the screw in by hand to start, then tighten snugly—do not over-torque
• Keep removed hardware organized and compare sizes before installing

Plastic hinge bushing (Thimble) for a 3/8 inch pin. Order 66036-1 for the 1/4 inch pin.