Need Help?
Call
Broken ice enclosure causing ice jams or warm air leaks? Replace this ice path housing. Moderately easy DIY repair—remove one screw and wire harness.
Upon receipt of part (in 2 days), removed right panel (snapped on). Removed ice tray. Removed one screw holding broken tray. Then removed plug from motor/solenoid. Next, moved motor/solenoid from old cracked tray to new one. All holes aligned exactly. Replaced shelf/motor in freezer, and reconnected cable from motor to freezer wall. Put one screw back in. Then replaced right-side snap-in panel. Finally, slid in ice-tray itself onto the new shelf. Tested okay. Read more
Usually ships within 4 - 14 days
White freezer door handle for side-by-side refrigerators. Replace cracked, yellowed, loose, or missing handles to restore grip and appearance.
I took out the old screws which were a bit of a challenge. The new handles seemed too short. Learned they needed to be warmed to be more flexible. Put near fireplace for a few minutes. Then with a little pressure they snapped into place and I screwed them in. Looks like new again. Read more
Fix a refrigerator that runs constantly or won't maintain proper temperature. This cold control thermostat regulates cooling cycles. DIY repair.
I ordered a new one from AppliancePartsPors.com which I got the next day, and installed it. Read more
Fix a refrigerator that clicks but won't start or runs warm. This compressor start relay restores reliable startup. Simple DIY repair in under an hour.
Removed old. Installed new. Read more
Fix frost buildup in your freezer with this defrost heater. Restores proper cooling when ice accumulates on evaporator coils. Moderate DIY repair.
Replaced the heater coil and the Thermostat underneath the freezer floor. 1. Unplug the Power, allow the ice build-up to thaw (Use hair-dryer). 2. Remove the heavy duty Plastic Tray (Freezer Floor) very carefully (the left and right side lips of the tray are snapped behind the sides of the freezer frame, un-snap the lips using flat spatula) . Gently pull out the Tray 3 Remove the plastic shroud (cold air diverter) at the back of freezer section (after removing the screw, tuck-up the shroud to... Read more
Fix frost buildup in freezer or refrigerator not cooling properly. This defrost heater and thermostat assembly restores normal defrost cycles.
Black plastic shim that supports and aligns the door hinge assembly. Replace if broken, cracked, or missing to restore proper door alignment.
A broken cam can be bad news. The door can swing open from its own weight. I ordered a door closure kit (cams) plus shims. My fridge needs a stack of shims on the fridge door to align it vertically. The old shims had broken and pieces fell out. The lack of support may have caused the cams to fail since they sit on the shims. I used the new shim as a pattern to fabricate a single aluminum shim for more strength. The head of the screw anchoring the lower cam was torn up. Fortunately, it... Read more
Seals refrigerator or freezer door to maintain proper temperature and reduce energy loss. Replace if worn, cracked, or loose. Verify fit with model.
Directs water into the ice maker fill cup. Replace this funnel if cracked, broken, or missing to ensure proper water flow and prevent spills during ice production.
Replacement door handle for your refrigerator or freezer. Installs on the door front to restore a secure, comfortable grip. Replaces cracked or broken handles.
Replaces the water supply tube that connects your household line to the ice maker and dispenser. Order when original tubing is cracked or leaking.
Motor won't start or keeps shutting off? This refrigerator overload protector stops the motor when it overheats, preventing damage and unsafe operation.
Fix a refrigerator that won't cool or clicks without starting. This PTC starter relay helps the compressor engage properly. DIY repair in under 30 minutes.
Refrigerator made a clicking sound in box connected to compressor. Googled it and found the reason could be the 2 parts I ordered. Replaced them and it runs fine now. Read more
Roller bracket that mounts refrigerator rollers to the base frame. Replace if your bracket is cracked, bent, broken, or missing to restore stability.
Machine screw secures appliance panels, brackets, and internal components. Replace missing, stripped, or worn fasteners for reliable assembly.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.