Magic Chef Refrigerator Parts

This refrigerator ice bucket stores ice made by the icemaker and positions it for dispensing. Replacing a cracked or warped bin restores smooth ice flow and helps prevent jams, spills, and mess inside the freezer.

• Holds and contains ice cubes in the freezer for easy access and dispensing
• Interfaces with the auger/crusher assembly in dispenser-equipped models
• Helps correct issues like ice jamming or inconsistent dispensing caused by a damaged bin
• Addresses visible damage such as cracks, chips, warping, or a bucket that won't seat properly
• Can reduce stray ice or moisture under/around the bin when the original is compromised

• Unplug the refrigerator and turn off the icemaker/water supply before starting
• Remove the old bin; transfer any auger/crusher components from the original if your model uses them
• Seat the new bucket fully so it latches/aligns correctly with the drive
• Restore power and verify proper dispensing operation

This defrost timer controls the automatic defrost cycle in select refrigerators and freezers, switching between cooling and defrost to clear frost on the evaporator. It helps maintain stable temperatures and prevents heavy ice buildup and long run times. What it does:

• Alternates the system between cooling and defrost on a timed schedule
• Sends power to the defrost heater during defrost, then returns power to the compressor and fans
• Failure can cause heavy frost on the evaporator/back freezer wall
• May lead to warmer temperatures, constant running, short cycling, or no-cool if stuck in defrost

• 1 defrost timer

• Disconnect power before servicing
• Access location varies by model
• Note wire positions and transfer them one at a time to the new timer
• Mount securely in the same orientation as the original and verify normal cycling after power is restored

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

Size: 1/4 inch. Nut for plastic water line.

Ice maker water line: 1/4x 8ft.

This evaporator defrost heater melts frost from the evaporator coil during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice buildup that restricts cooling and leads to warm spots. What it does:

• Heats the evaporator coil to clear frost/ice during defrost
• Helps maintain proper airflow between freezer and fresh food sections
• Typical symptoms: heavy frost on the back panel/evaporator, weak cooling or rising temperatures
• Also cause evaporator fan noise from ice contact and longer run times

• 1 evaporator defrost heater

• Disconnect power before servicing; allow any ice to thaw
• Access the heater behind the freezer's rear panel; avoid damaging fins or refrigerant lines
• Secure the heater and route wires exactly as original, keeping them clear of the fan and sharp edges
• Restore power and verify the defrost cycle per the service procedure

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This black refrigerator toe grille covers the lower front opening, protecting internal components and helping guide airflow through the condenser while giving the appliance a clean, finished look. Replace a cracked or missing grille to restore fit and appearance.

• Helps direct airflow to the condenser area for proper ventilation
• Shields the machine compartment from bumps and debris
• Provides a finished, uniform look along the base
• Replace if cracked, warped, tabs are broken, won't stay attached, or rattles

• Disconnect power before servicing and wear cut-resistant gloves
• Remove the existing grille by releasing clips or removing screws (as designed)
• Align the new grille with mounting points and secure with the original fasteners
• Ensure ventilation slots are clear and unobstructed after installation

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

This ice enclosure is the molded housing for the refrigerator's ice compartment. It supports and protects the ice dispensing components and guides ice into the chute or bin, helping maintain proper alignment and smooth dispensing. What it does:

• Provides structural support for the ice bucket/auger and related dispenser components
• Helps guide ice from the compartment into the chute/bin to reduce spills and jams
• Aids in maintaining alignment and a consistent cold zone around the ice area
• Typical symptoms of failure: cracked/broken housing, ice bin won't seat securely, ice jams or intermittent dispensing, frost/ice buildup in the ice compartment

• One ice enclosure

• Disconnect power; remove the ice bin before service
• Note screw locations; detach the old enclosure and any connected clips or wiring
• Transfer any brackets or hardware from the original enclosure; reuse existing fasteners
• Mount the new enclosure without overtightening; restore power and verify normal dispensing

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Fresh food section. Color: clear. Measures about 3 inches in diameter.

This top door hinge is the butt hinge assembly that mounts to the cabinet at the top of the refrigerator door, supporting the door and allowing smooth swing. Replacing a worn hinge restores alignment and a reliable seal.

• Provides the upper pivot point for the door
• Keeps the door aligned so the gasket seals correctly
• Wear or damage can cause sagging, rubbing, squeaks, or a door that won't close fully
• Helps reduce air leaks and temperature swings near the door

• Disconnect power and remove items from the door to reduce weight
• Support the door from below; remove the hinge cover and mounting screws
• Note the position of any shims/spacers and transfer them to the new hinge
• Reinstall, align the door, tighten screws, and ensure proper gasket contact

This is the center hinge for the refrigerator doors. It supports and aligns the doors at the midpoint so they open smoothly and seal properly, helping maintain temperatures and reliable day-to-day operation.

• Provides the middle pivot point between the upper and lower doors
• Keeps door alignment and spacing correct for a tight gasket seal
• Common symptoms: door sagging or rubbing, squeaking/grinding, door not closing or popping open, uneven gaps
• Replace if the hinge bracket or pin is bent, worn, or corroded

• Disconnect power and clear items from the doors before starting
• Support the doors; a second person is recommended when removing hinge screws
• Note the order of any shims/spacers or washers and transfer them to the new hinge
• After installation, align doors and verify full gasket contact all around