Magic Chef Screws, Nuts, Washers

A genuine replacement screw used to secure components on compatible Whirlpool appliances. This small fastener restores proper assembly and helps stop loose panels, trim, or internal parts from rattling or shifting during operation. What it does:

• Secures panels, brackets, or components to restore proper fit and reduce vibration noise
• Replaces missing or stripped fasteners that cause parts to sit unevenly or move during cycles
• Helps maintain safe, stable appliance operation by keeping components fastened

• Use the matching screwdriver or bit to avoid stripping the head; do not force a damaged screw
• Hand-start threads before using a driver to prevent cross-threading
• Replace any additional corroded or damaged screws with matching fasteners for best fit
• Disconnect power and follow appliance-specific safety steps before accessing internal parts

Size: 8abx3/8 - blk)

This genuine replacement screw secures appliance panels and components, restoring proper fit and stopping movement. Use it when a missing or damaged fastener causes loose trim or rattling. What it does

• Secures panels, brackets, and small assemblies to restore proper fit
• Helps eliminate rattling, vibration, or misaligned trim caused by a missing or stripped screw
• Replaces lost or damaged fasteners during maintenance or part replacement
• Matches OEM fit for reliable fastening where specified in diagrams

• Use the matching screw location shown in the appliance diagram; do not force or overtighten
• Use the correct screwdriver or bit to avoid stripping the head
• Disconnect power and follow appliance safety procedures before accessing internal components
• If threads are damaged, replace with the correct OEM fastener rather than reusing a compromised hole

This is a flat plain washer used to distribute load and space hardware on appliance assemblies. It helps keep bolts and screws seated and reduces wear on mating surfaces for more secure fastener connections. What it does:

• Provides a flat bearing surface to spread clamp load and protect parts from fastener damage
• Maintains proper spacing and alignment for mounted components
• Helps prevent fastener loosening from vibration when used with the correct bolt or screw
• Commonly used on chassis, suspension, and bracket connections

• One plain flat washer

• Disconnect power and water supply before servicing the appliance
• Replace only with the same washer size and thickness as the original for proper fit
• Tighten fasteners to secure but avoid over-torquing which can deform the washer

This screw is a factory-style mounting fastener used to secure appliance panels and components. It replaces worn, stripped, or missing screws to restore proper fit and reduce rattling. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces damaged or corroded fasteners that can cause loose parts
• Helps maintain safe, stable operation of moving or load-bearing assemblies

• Turn off power and unplug the appliance before servicing
• Use the correct driver bit and match thread engagement to avoid stripping
• Tighten snugly but avoid over-torquing which can crack plastic or strip threads
• Wear eye protection and keep small parts away from children and pets

Screw (bur) is a fastener that secures panels, brackets and small assemblies on select Whirlpool appliances. Replacing a missing or damaged screw restores proper fastening and helps reduce vibration, rattling and misalignment. What it does:

• Fastens panels, mounting brackets and small internal or external components to the appliance frame.
• Replacing a stripped or missing screw prevents loose parts and restores a secure fit.
• Symptoms of a failing screw include rattling, vibration, panels or trim that do not sit flush, or components that move during operation.
• Commonly used where a short machine screw or trim fastener is required for assembly.

• Disconnect power before beginning any service.
• Use the correct screwdriver or driver bit and install straight to avoid stripping the head or threads.
• Do not overtighten — snug until secure to prevent damage to threads or parts.
• Keep removed fasteners organized and replace any damaged screws with the exact OEM fastener.

A stainless pushnut used to secure shafts, studs, or small components with a quick, push-on retainer that resists corrosion. Keeps parts fastened without threading or additional hardware for a clean, low-profile fit. What it does:

• Acts as a push-on retaining nut to hold shafts, studs, or fittings in place
• Provides a corrosion-resistant stainless finish for wet or high-humidity areas
• Prevents components from sliding off axles or posts during normal operation
• Commonly used on control shafts, knobs, or small internal assemblies

• Turn power off and unplug appliance before servicing to avoid shock or injury
• Push onto the post or shaft until fully seated; a firm press or light tap may be required
• Use appropriate hand tools or pliers with protection to avoid damaging the part
• Replace with identical part number to ensure fit and function

This 8-32 x .340 machine screw secures small appliance panels and components for a reliable fit. It's a simple replacement fastener when original screws are missing, stripped, or worn. What it does:

• Fastens panels, brackets, and internal components where 8-32 threads are required
• Provides a short, firm hold for thin materials and assemblies
• Useful when original mounting screws are lost or damaged
• Matches OEM thread size and length for correct fit in designed screw bosses

• One 8-32 x .340 machine screw

• Use the correct screwdriver or nut driver to avoid stripping the head
• Do not overtighten; snug to secure without deforming plastic or stripping threads
• Confirm screw length and thread size match the original before installation
• Disconnect power and follow appliance safety precautions when accessing internal parts

A small replacement screw used to secure appliance panels and components so assemblies stay aligned and stable during normal use. Simple, direct fix for loose trim, panels, or mounting points. What it does:

• Secures panels, brackets, or small components to prevent rattling and movement
• Restores proper alignment where a missing or damaged fastener causes gaps
• Helps stop vibration-related noise from loose parts
• Functions as the original-style fastener matching OEM fit and purpose

• Disconnect power and water to the appliance before servicing where applicable
• Use the correct screwdriver or bit to avoid stripping the head
• Thread the screw in by hand to start, then tighten snugly—do not over-torque
• Keep removed hardware organized and compare sizes before installing

This is a replacement screw used to secure appliance panels and components so parts stay firmly mounted and functioning. Use it to replace a missing or damaged fastener for a secure repair. What it does:

• Fastens panels, brackets, or small components to prevent loosening or vibration
• Helps stop rattling, shifting, or gaps caused by a missing or stripped screw
• Restores proper alignment of mounted parts after repair or maintenance

• Use the matching driver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or surrounding parts
• Disconnect power and follow manufacturer safety guidelines before servicing the appliance
• Replace like-for-like: screw size and head type match the original before installation