Parts for Generac 006673-0: Main Assy Parts

This replacement charging jack is designed for a generator. The charging jack allows the user to charge components connected to the jack. While the jack does not include moving parts, it can suffer from internal failures. The most common problems include damage or corrosion to the jack itself, as well as damage to the connector terminals or to the wires themselves. If the charging jack is not working, it will likely need to be replaced.To replace the charging jack, users will need to disconnect the spark plug, and then access the interior of the generator. Disconnect the two wire connectors that connect the jack to the rest of the wiring harness. Next, unscrew the housing of the jack and then pull the entire jack connector free of the generator. Install the new charging jack by reversing these steps. This genuine OEM replacement part is sold individually. It fits certain Generac generator models.

This is an M6 G8.8 screw that has been tempered for added strength. It is made of carbon steel and is ideal for use in lawn mower engines and other pieces of equipment. It measures 28 millimeters in length with an outside diameter of six millimeters. This Generac replacement screw can be used in any application where an M6 1.0 x 28 is required as a replacement for a broken or stripped screw. Routine maintenance may reveal missing or damaged screws that need to be replaced. Removal and replacement are simple. This M6 screw requires a hex wrench for removal. If the screw is in a difficult location, a socket with a hex wrench can be used. Install the new screw and tighten firmly but not overly tight as this can strip the threads. This M6 1.0 x 28 G8.8 screw is an individually sold Generac part. It is used in lawn mowers, lawn tractors, weed eaters, and other pieces of equipment that require heavy-duty screws for assembly.

This flange hex nut is a common piece of hardware used in a range of machines and engines. The flange on the nut helps to provide a secure connection, and it can reduce the amount of strain on the pieces that are being held together. If there is damage to these parts, or any are missing, it could cause vibrations in the machine or parts could become loose. Over time, flange hex nuts can become corroded or worn. Replacement is usually easy depending on the location of the nut.This flange hex nut is typically found in certain generator models from Generac. This OEM part is high-quality and has been sourced from the manufacturer. It is sold individually.

This replacement part is a "single" wheel typically used on generators. This is a genuine replacement part made by Generac. Wheels are an important part in this appliance as they allow the user to move the generator with ease. This type of appliance is made to be easily transported and the wheels make that possible. A new wheel might be needed if the current ones are worn down or broken in any way. It is not unusual for this part to require replacement after years of normal use as the wheels might lose traction overtime. Be sure the appliance is completely powered down and cooled off before attempting to replace this part as the user will need access to the bottom of the generator. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with generators made by Generac.

This exhaust gasket is an authentic OEM part sourced directly from the manufacturer specifically for use on Generac generators. The exhaust gasket seals the connection between the exhaust manifold and the side of the engine. The gasket prevents exhaust gasses from leaking out and prevents contaminants from coming into the exhaust system. If the generator's engine starts sounding very loud, loses power, has a burning smell, or loses fuel efficiency, the exhaust gasket could be worn and need to be replaced. All gaskets should be inspected on a regular basis to maintain the life of the generator.Allow the generator to cool before working on it. Wear safety gloves and remove the spark plug for safety. Use a screwdriver and remove the muffler housing. Next, remove the muffler and exhaust pipe. Pull the exhaust gasket off and install the new gasket. Reassemble the generator using reverse steps. Install the spark plug and start the generator to ensure it is back together correctly.This exhaust gasket is sold individually and is the muffler side gasket. This gasket is designed specifically for Generac generators.

This replacement part is an electric start contactor assembly intended for use with generators. It is part of the generator's ignition system.A new electric start contactor assembly might be needed if the generator is unable to start or is struggling to start. If the start contactor is missing or damaged, the generator might be unable to start. It is common that this part might become worn down over time and should be replaced after years of normal wear and tear. Be sure the generator is powered down and cooled off before attempting to replace or repair this part. This is a genuine OEM replacement part manufactured by Generac. This part is sold individually.

This OEM replacement part is a starter motor for generators. The starter motor spins the flywheel to start the generator when the power is turned on. If the generator is no longer turning on, then it might be time to replace the starter motor. Luckily, replacing a starter motor is a fairly simple repair. Before beginning, make sure the generator is turned off. Once powered off, remove the cover of the generator to gain access to the starter motor. Once located, remove the mounting bolts that attach the starter motor to the generator. After that, replace with the new starter motor and fasten the bolts to hold it in its proper position.This genuine replacement part is sold individually and is compatible with Generac generators.

This part is a replacement brush holder. It is intended to repair a defective or broken brush holder in generators.This part is intended to hold the carbon brushes and ensure that they are not easily lost or detached. This brush holder should be replaced if the current one is broken, cracked, detached, or otherwise rendered ineffective. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process.This brush holder is a genuine OEM part from Generac made of durable materials and is sold individually. It is suitable for use with generator models that have been manufactured by Generac, Siemens, Honeywell, and some other brands.

This is an automatic voltage regulator that is used on many generators. Depending on the model of the generator, it can be located in the main control box, under the alternator rear cover, or in the alternator terminal box. It senses the voltage from the generator terminals and compares it to a stable reference. This is used to adjust the flow to the right level. If the automatic voltage regulator is damaged, the generator will experience a loss of voltage that causes the machine to shut down.A malfunctioning automatic voltage regulator will need to be replaced. If it isn't, the generator may not run. If it does run, it can cause serious damage to the generator. Test the main circuit breaker before testing the wiring. Next, adjust the automatic voltage regulator. If this doesn't help, check the rotor brushes. If the generator is still not working correctly, the automatic voltage regulator should be replaced. Make sure to turn it off and unplug it before doing so.This is a genuine OEM replacement part that is directly sourced from the manufacturer. The automatic voltage regulator is sold on an individual basis. The component is made for use with several generators manufactured by Generac.

This part is a replacement fuel cap. It is intended for use with generators. Fuel caps are intended to prevent gas spills and leaks, as well as stop contaminants from entering the fuel supply. If the fuel camp is lost or broken, it should immediately be replaced with a genuine OEM part. When working on or near an engine, always ensure that the equipment is powered off and completely cool before beginning any repairs.This fuel cap is suitable for use on generators manufactured by Generac, Honeywell, Siemens, and some other brands. It is a genuine OEM part from Generac and thus is made of high-quality, durable materials. It is sold individually.

This fuel filter keeps dirt and foreign objects out of the fuel system of Generac generators. Fuel, particularly when stored in portable fuel tanks, is prone to getting dirt and debris in it. Before using it in a generator or other piece of equipment, the debris needs to be removed. If the dirt and debris are not removed from the fuel, it can enter the fuel system and cause damage. The fuel filter prevents this from happening.Fuel filters need to be examined and replaced as part of routine maintenance. A visual inspection will show if the filter is dirty or not. If dirty, the filter is easily removed with a pair of pliers. The new filter can be put into place using your hands. The process normally takes less than twenty minutes. All dirt and contaminating particles are not visible to the naked eye. The fuel filter should be replaced according to a scheduled maintenance plan, regardless of visible dirt and debris. This OEM fuel filter comes directly from the manufacturer and is used in Generac portable generators. The overall part is made of plastic and contains a mesh filter. It is sold individually.

This replacement part is roll over valve intended for use in generators. This is a genuine replacement part made by Generac. This part is responsible for burning off fumes created by the generator.A new roll over valve might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide or manual for the appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with generators made by Generac.

This part is a 12-volt battery used on portable generators. The purpose of a battery is to provide the current needed to start the portable generator.A new 12-volt battery may be needed if the battery is dead and cannot be jump-started. Over time, batteries become weaker and need to be replaced after normal wear and tear over a period of time. If the portable generator will not turn on, it could be a result of a battery that has died or gone completely bad. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Use extreme care when handling a battery.This 12-volt battery is a genuine Husqvarna part. It is sold individually. This particular 12-volt battery is compatible with outdoor power equipment that are manufactured by the Husqvarna brand and the Generac brand.