Parts for Lg LTG4715BM/00: Main Unit Parts

Replace a gas range burner when flames are uneven, won't ignite, or produce yellow flames. Direct swap installation takes 10-15 minutes with basic tools.

Burner not heating or heating unevenly? This surface element restores full heat output on your range. Straightforward DIY fix in under an hour.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Range insulator cushions components, reduces vibration, and prevents heat transfer. Restores proper spacing when original insulator wears or fails.

Protective insulator cushion for ranges. Installs between components to dampen vibration and prevent rubbing. Replace if cracked, worn, or missing.

Insulator pad for electric and gas ranges. Protects components from heat damage. Replace if cracked, deteriorated, or missing to maintain proper insulation.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Replacement screw secures panels and components in your microwave. Install when original hardware is stripped, rusted, or missing to stop rattles.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This knob assembly is the replacement control knob that lets you select cycles, temperatures, or settings on your appliance. It restores a solid grip and precise control when the original knob is worn or broken. What it does:

• Replaces a damaged, cracked, or missing control knob so you can change settings easily
• Fits onto the control shaft to provide a secure, user-friendly interface
• Restores tactile feedback and reduces slipping or spinning on operation
• Common symptom fix: loose, hard-to-turn, or non-engaging knob that won't change settings

• Disconnect power before servicing to avoid electric shock.
• Pull the old knob straight off the control shaft; align and push the new knob onto the splined shaft until seated.
• If the knob is tight or stuck, use a cloth and gentle pulling—avoid excessive force to prevent shaft damage.
• If the control shaft or underlying switch is damaged, replace the damaged components rather than forcing the knob.

Control knob assembly for gas range burners. Mounts on the front control panel. Replace if knobs are cracked, broken, loose, or missing.

Range not heating or control panel unresponsive? This control board assembly restores oven functions. Moderate difficulty repair requiring basic tools.

The PCB Assembly, Sidekey is an OEM replacement part for LG  ranges. This printed circuit board assembly is responsible for controlling the functions of the control panel on the side of the range. It communicates with all electronic components to operate the cooktop burners, oven lights and fans, and programming features.   

Causes of a bad PCB assembly can include corrosion of printed circuits over time due to heat exposure, moisture damage, or component failure.

Symptoms of a bad PCB assembly include: 

• Cooktop burners not working properly or unresponsive to control panel commands
• Inability to turn on oven lights or fans
• Programming features like timers or temperatures not functioning correctly
• Blank or unresponsive control panel displays

This OEM LG part is also compatible with Sears/Kenmore ranges. Replace yours today with this genuine electronic control board and upgrade the functionality of your electric range oven.

Fix a range that won't heat, cycle on, or respond to buttons. This control board assembly interprets inputs and restores reliable oven operation.

Fix an unresponsive oven control knob or broken control dial. This encoder board detects knob position and sends signals to adjust temperature settings.

Secures panels, brackets, and trim on your gas range. Replace this self-tapping fastener if it's missing, stripped, or damaged to restore alignment.

Replacement screw for electric and gas ranges. Secures panels, brackets, and internal assemblies. Restores tight fit when original is missing or stripped.

This heater cover is the replacement housing that protects the dryer heater assembly and helps direct airflow for reliable drying performance. It restores proper heater positioning and helps prevent contact with heating components. What it does:

• Protects the heater assembly and surrounding components from debris and direct contact
• Helps channel airflow through the heater area for consistent drying
• Can reduce rattling or noise caused by a damaged or loose heater cover
• May be replaced when cover is cracked, warped, or missing fasteners

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury
• Inspect mounting tabs and fasteners; replace any damaged clips or screws for secure fit
• Minor disassembly of the dryer cabinet may be required; keep track of removed screws and panels
• If you smell burning or see damaged wiring, stop.

This heater cover protects the dryer heater assembly and helps direct airflow for proper heating performance. It replaces a cracked or damaged cover to restore safe operation and part alignment. What it does:

• Shields the heating element and internal components from debris and accidental contact
• Helps channel airflow through the heater for efficient drying
• Can prevent rattling or vibration caused by a loose or broken cover
• Common symptom: damaged cover may be noticed when replacing the heater or after impact/overheating

• Disconnect power before accessing the heater assembly; allow components to cool fully
• Follow the appliance service manual for disassembly/reassembly and use correct fasteners
• Inspect adjacent components (heater element, terminals, mounting clips) and replace if damaged

Factory-style screw for securing panels, brackets, and assemblies on gas ranges and cooktops. Replace if missing, stripped, or damaged during repairs.

Fixes weak or uneven flames on gas range burners. This nozzle meters fuel flow to each burner for balanced heating. Direct replacement part.

Replace a faulty gas range burner nozzle if flames are uneven, yellow, or won't ignite properly. This part meters fuel flow to each burner for balanced heating.

Pipe assembly for gas ranges. Connects gas supply lines within your range. Replace if cracked, corroded, damaged, or leaking to restore safe operation.

The Pipe Assembly is an OEM part for LG ranges and cooktops. This manifold is responsible for housing the gas valves and safely distributing gas to each burner. It works to allow control and adjustment of burner flames.

Over time, gas valves and other internal parts can become worn or damaged due to regular use and exposure to heat. Causes of a bad Pipe Assembly can include faulty gas valves that do not properly regulate gas flow, damage to internal tubing or gas lines, or worn seals and gaskets.

Symptoms of a bad Pipe Assembly include:

• Inconsistent or irregular burner flame sizes
• Difficulty adjusting burner flames
• Flames that become too high or too low and unstable
• Front burners that do not ignite or light unevenly
• Gas smells coming from the range

This OEM LG part is also compatible with some Kenmore models.

This replacement outer housing case provides a durable protective cover for internal components, restoring the appliance's exterior fit and protection. It helps maintain proper component alignment and prevents dirt and moisture from entering sensitive areas. What it does:

• Protects internal components and wiring from damage, dust, and moisture.
• Restores proper alignment and secure mounting for controls or assemblies attached to the case.
• Reduces rattles, vibration noise, or loose-feeling panels caused by cracked or warped housing.
• Helps prevent minor water intrusion into internal compartments when the original case is damaged.

• One replacement outer housing case

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Installation typically requires basic tools (screwdriver set); keep fasteners and trim in a safe place during removal.
• Handle the replacement carefully to avoid scratching or cracking the new case; ensure all clips and screw locations line up before final fastening.
• If seals, gaskets, or attached trim were removed, inspect and replace as needed for proper reassembly.

Outer housing case that protects internal components on your gas range. Replace if cracked, warped, damaged, or missing to restore structural support.

This vent assembly is the chassis-mounted exhaust housing that directs dryer airflow from the drum to the external vent system, restoring proper air evacuation and reducing heat build-up in the cabinet. It replaces a damaged or worn outlet housing to help the dryer vent correctly. What it does:

• Channels hot, moist air from the dryer to the exhaust duct to improve drying performance.
• Helps maintain proper airflow; common symptom of failure is longer dry times or incomplete drying.
• Prevents air leaks at the cabinet exit that can cause heat buildup or lint accumulation.
• Replaces cracked, broken, or warped housing that can rattle or allow debris to escape.

• One vent assembly as shown.

• Disconnect power (and gas if applicable) before starting any repair.
• Remove the dryer front or rear access panels to access the housing.
• Inspect surrounding seals and ducting; replace any damaged gaskets or ducts to ensure a tight seal.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

Secures the gas burner nozzle in your range cooktop. Replace this holder if it's cracked, broken, or no longer holding the nozzle firmly in position.

Fix misaligned or wobbling burner flames with this nozzle holder. Secures the nozzle in place to restore proper gas flow and even heating on your range.

Fix weak flames or uneven heating on your gas range. This surface burner assembly restores proper heat output and flame control. Standard DIY repair.

Fix uneven heating or a burner that won't ignite with this gas range surface burner assembly. Mounts under the cooktop for reliable flame control.

Replace your range's outer door trim to restore a finished appearance and maintain proper door seal alignment. Direct-fit frame for compatible models.

This is the inner glass panel that sits on the inside of the oven door, forming part of the insulated door assembly. It helps retain heat inside the oven cavity and protects the outer door glass from direct exposure to high temperatures. Replace this glass if it is cracked, shattered, or has visible damage that could compromise oven heat retention or safety.

This air guide directs cooled air inside the refrigerator compartment to help maintain even airflow and temperature distribution. Replaces a damaged or missing guide to restore proper venting and help reduce uneven cooling. What it does

• Channels cold air from the evaporator vent into the fresh food compartment for more consistent cooling.
• Helps reduce warm spots or uneven temperatures near shelves and door bins.
• Prevents direct airflow onto stored items, protecting sensitive foods from frost or drying.
• Fits behind vents or above crisper drawers to guide airflow where needed.

• One (1) air guide

• Always unplug the appliance or switch off power at the breaker before servicing.
• Typically installs without specialty tools; you may need to remove shelves or drawers for access.
• Handle plastic parts carefully to avoid cracking; align tabs and snap into place until secure.
• If airflow issues persist after replacement, check vents, damper, and evaporator fan for related faults.

Clear viewing pane for range oven doors. Replace when cracked, shattered, chipped, or stained to restore visibility and a clean, finished appearance.

Inner door cover panel for electric and gas ranges. Replace this part if your existing panel is cracked, broken, damaged, or missing from the oven door.

Bracket that anchors the handle to your range oven door. Replace if cracked, stripped, or broken to restore secure handle attachment and alignment.

Replacement door frame for electric and gas range ovens. Replace this structural component if cracked, bent, or damaged to restore door appearance.

Decorative panel for your range oven door. Installs on the exterior door surface to refresh appearance. Replace if cracked, chipped, or discolored.

The inner cover protects internal components and wiring by covering the appliance's cabinet opening, helping prevent debris entry and accidental contact. It restores safe access and maintains the appliance's internal layout and airflow. What it does

• Shields internal electronics, wiring and assemblies from dust and debris
• Helps prevent accidental contact with energized components
• Restores proper internal clearance and part alignment after repair
• Can address symptoms like visible damage, exposed wiring, burning odor or intermittent operation caused by a compromised cover

• Replace with power disconnected and appliance unplugged to avoid shock
• Verify correct orientation and secure all mounting tabs/screws; do not force into place
• Inspect adjacent wiring and components for damage while the cover is removed
• Use only the part number shown for exact fit

Secures and pivots your range door smoothly. Replace when doors drift, rub, or won't align properly. Confirm fit with your model number before ordering.

Shield plate for electric and gas ranges. Protects internal components from heat and debris. Replace if cracked, bent, damaged, or missing for proper range operation.

Fix a gas range that won't start, has dead controls, or won't respond to buttons. This main control board assembly manages electronic functions.

This is a lever supporter that sits behind the control knob on a range, providing structural support for the knob shaft and ensuring the knob engages properly with the selector switch or valve stem. It helps maintain correct knob alignment and rotational feel. Replace this part if the control knob feels loose, spins freely without engaging, or if the original support is cracked or broken.

Wire harness for gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose or broken.

Fixes intermittent power or control issues caused by damaged wiring. This harness restores electrical connections between range components for reliable operation.

Range controls not responding or features intermittent? This wiring harness restores power and signal connections between components for reliable operation.

If your range control panel is loose or cooking functions are erratic, the PCB supporter may be cracked. This mounting bracket secures the circuit board.

Support bracket that secures the control board assembly inside your range. Replace if the bracket is cracked, bent, or missing to properly mount the PCB.

Fix an oven door that won't stay open or slams shut with this range door spring. Simple DIY repair requiring only a Phillips screwdriver, 30 minutes.

A replacement window glass for microwave doors that restores a clear viewing area and protects internal components. Fits the oven door assembly to help you monitor food without opening the door. What it does:

• Replaces cracked, cloudy, or broken microwave door glass to restore visibility
• Helps contain heat and food splatter inside the oven cavity when the door is closed
• Restores the door's finished appearance after impact or wear
• Safe symptom linkage: use when door glass is chipped, shattered, or severely scratched

• Disconnect power to the appliance before service to avoid electrical shock.
• Handle glass carefully and wear cut-resistant gloves and eye protection.
• May require partial door disassembly; keep track of screws and clips for reassembly.

Factory service parts assembly for electric and gas ranges. Replaces worn, damaged, or missing multi-component grouping. Restores original configuration.

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

Replace a cracked, warped, or worn top plate on your gas range. This metal surface panel installs on the cooktop frame to restore appearance.

Idle packing bushing for electric and gas ranges. Replaces worn, cracked, or missing bushings. Ensures proper fit and cushioning for range components.

Oven rack for electric and gas ranges. Provides stable surface for cookware during cooking. Replace if bent, warped, cracked, or missing.

Replace a damaged or missing motor cover on your gas range. This protective cover shields internal motor components from debris and damage.

Surface burner grate for gas ranges and cooktops. Sits atop burner to support cookware during cooking. Replace if warped, cracked, broken, or chipped.

The Grille Assembly is an OEM part for LG cooking ranges and range tops. It provides an additional flat-top cooking surface between the standard burner elements. The grille assembly itself is constructed of heavy-duty materials designed to withstand high heat levels while cooking.

Causes can be wear over time under heavy usage, accidental damage from cookware or cleaning, or failure of the heating elements underneath the plate.

Symptoms of a bad griddle plate include:

• Uneven or slow heating of the surface
• Warping or bending of the plate
• Scratches, cracks, or other surface damage
• Loose or missing mounting hardware

This LG part is also compatible with some Kenmore models.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas burner nozzle. Controls gas flow for proper flame size. Simple install with basic tools.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas range burner nozzle. Controls gas flow for optimal flame performance. DIY install.

Fixes burners that won't light or ignite properly on your gas range. This gas valve assembly controls gas flow to surface burners. Moderate DIY repair.

Fix burners or oven not lighting with this gas valve assembly. Controls gas flow to restore safe ignition and consistent heating in your range.

Gas range won't ignite or heat properly? This valve assembly controls gas flow to your oven and burners. Restores ignition and safe operation.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

Replace your worn or damaged range burner to restore consistent flame and even heat distribution. Directs gas through ports for reliable cooking performance.

Burner head controls ignition and flame distribution on your gas range. Fixes weak flames, uneven heating, or burners that won't light properly.

Replace a cracked, discolored, or missing burner cap that's causing uneven flames or allowing spills into the burner assembly. Fits over the burner head.

If your gas range has uneven flames, yellow or orange flames, or won't light properly, a damaged burner cap is often the cause. This part restores safe, even heat distribution.

Protective cover that fits over the burner head on your gas range cooktop. Replace if cracked, chipped, broken, or missing to restore appearance.

Uneven flame or poor heating? This gas range burner cap directs flames evenly across cookware and contains sparks. Simple snap-on installation.

Fix intermittent power issues or control failures with this range main wiring harness. Connects electrical components for proper signal communication.

Cable assembly for gas ranges. Replaces worn, damaged, or broken cable connections inside your range. Essential structural component for proper operation.

Fix control issues or power failures with this gas range cable assembly. Restores reliable operation when wiring is damaged, burned, or has loose connections.

Fixes unresponsive controls or features not working on your gas range. This cable assembly restores power and signal connections between components.

Fix burners that won't light or controls that don't respond with this range wire harness. Restores electrical connections between components. Moderate DIY.

Bending pipe for gas ranges. Connects gas supply lines between burner valves and manifold. Replace if cracked, bent, corroded, or leaking at connections.

Bending pipe for gas ranges. Connects gas supply lines within the range assembly. Replace if bent, cracked, or damaged to restore proper fit and alignment.

Fix unresponsive control panel buttons with this tactile switch replacement. Restores reliable button response. Simple DIY repair, typically under 5 minutes.

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

Microwave won't turn on or has no power? A failed thermostat often causes complete power loss. Moderate DIY repair requires disassembly to access.

Replace your range's wire harness if the existing wiring is damaged, frayed, or showing signs of wear. Connects electrical components inside your range.

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Replace a damaged or corroded wire harness in your range. This single-connection harness restores proper electrical connections when original wiring is frayed, melted, or broken.

Fix uneven cooking or baking in your range. This convection fan motor circulates hot air for consistent heat distribution. Moderate DIY repair.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Oven door hinge assembly for electric and gas ranges. Replaces broken, worn, or damaged hinges that prevent proper door operation or alignment.

Fix inaccurate oven temperatures with this range temperature sensor. Restores proper heating cycles when your oven runs too hot or cold.

Motor loose or vibrating excessively? This motor bracket secures the motor to the chassis, reducing vibration and maintaining alignment for quieter operation.

Fix loose or misaligned range components with this retaining ring. Secures parts in place to prevent excess movement and wear. Simple installation.

Fixes uneven baking and longer cooking times in your range. This convection fan blade restores proper air circulation for consistent oven temperatures.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

Replace a damaged range insulator if components overheat or rattle during operation. This small part cushions internal parts and prevents heat transfer.

This bracket secures the turntable motor to the microwave oven cavity base, keeping the motor properly aligned so the glass tray can rotate smoothly for even heating.

• Supports and positions the turntable motor beneath the oven floor
• Helps resolve issues like a non-turning glass tray or jerky rotation
• May correct intermittent grinding or scraping noises from the tray area

• Unplug microwave before servicing; high-voltage components can retain a charge
• Remove the unit from its install location if required for bottom access
• Access turntable motor from the underside; support the cavity to prevent damage
• Reuse existing screws and motor unless otherwise specified

Replace your damaged or broken range handle bar. This bar installs on the oven door, providing a secure grip for opening and closing. Order now.

Fix a humming or stalled range component with this AC synchronous motor assembly. Restores proper rotation when the motor fails to turn or makes noise.

This is the exterior side panel that attaches to the body of the range. It provides structural support and a finished appearance to the side of the appliance. Replace this panel if it is dented, scratched, rusted, or damaged during installation or use.

Replace your range oven light bulb when it burns out or dims. Restores interior visibility for safe cooking. Verify compatibility with your model number.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

A full-perimeter refrigerator door gasket that restores an airtight seal to help maintain proper cooling and reduce energy loss. Designed to replace a worn, cracked or torn door seal for reliable temperature control. What it does

• Seals the door to keep cold air in and warm air out, helping the appliance maintain set temperatures
• Common symptom: visible gaps, cracks, or tears in the gasket allowing cold air to escape
• Common symptom: excessive frost or condensation inside the compartment near the door
• Common symptom: refrigerator runs more often or works harder to maintain temperature
• Helps prevent food spoilage caused by inconsistent cooling when the original gasket fails

• One full-perimeter refrigerator door gasket

• High-level task: remove the old gasket and press the new gasket into the channel or attach per the manufacturer's method
• Gasket may require slight warming or alignment to seat evenly; follow OEM instructions for final fit
• Inspect mounting channel and clean surface before installation to ensure a proper seal
• Safety first: unplug the appliance before working on the door and take care not to damage trim or wiring

This pipe is the factory-design tubing used to route fluids inside the appliance, restoring proper flow and containment. Installing the correct pipe helps stop leaks and re-establish reliable fluid transfer where the original line has cracked or failed. What it does:

• Channels water or drain flow between internal components to maintain normal operation
• Prevents leaks by replacing cracked, split, or brittle tubing
• Helps restore proper filling, draining, or circulation when the original pipe is damaged
• Reduces risk of water-related faults and intermittent appliance behavior caused by compromised tubing

• One pipe as shown

• Turn off and unplug the appliance and shut off the water supply before starting work
• Remove any clips or fasteners carefully; save or replace clamps as needed
• Use the exact part number to ensure fit; route the pipe the same way as the original to avoid kinks

Gas pipe that connects burner components in your range. Replace if cracked, corroded, or damaged to restore proper gas flow and safe operation.

Gas supply pipe that connects the gas valve to the burners on your range. Replace if pipe is bent, cracked, or shows signs of wear or corrosion.

Burner nozzle holder for gas ranges. Secures the gas nozzle in the burner assembly. Replace if cracked, broken, or missing to ensure proper alignment.

Weak or uneven flame? This gas range burner nozzle controls gas flow for proper flame distribution. Restores consistent heat output and cooking performance.

Fix a burner that won't light or heat unevenly with this gas range burner assembly. Common repair for weak or inconsistent flames on cooktop surfaces.

If your gas cooktop burner won't ignite, flames are uneven, or the burner head is damaged, this surface burner assembly restores proper heating and flame control.

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

Lower cabinet support base that stabilizes your range and protects internal components. Replace if cracked, broken, or causing wobble for secure mounting.

This is a gas safety valve used in a gas range that controls the flow of gas to the burners or oven. It works with the ignition system to ensure gas is only released when proper ignition is detected. Replace this valve if the oven or burners fail to ignite, gas flow is inconsistent, or the valve does not shut off gas properly when the burner is turned off.

Base plate for electric and gas ranges. Provides structural support at the bottom of the appliance. Replace if cracked, broken, or missing. Easy install.

If your gas range burner won't ignite or heat unevenly, this surface burner assembly restores reliable flame and even cooking. Moderate DIY repair.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

Idle bracket for electric and gas ranges. Secures internal components in place. Replace if bracket is bent, cracked, broken, or missing during repair.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

This kit includes the nozzle accessories needed to convert a range from natural gas to liquid propane (LP) operation. It contains replacement orifices and any necessary fittings to ensure proper gas flow and burner performance on LP fuel. Use this kit when switching your gas range to propane, such as when moving to an area without a natural gas supply.

Accessory assembly for electric and gas ranges and wall ovens. Replaces damaged, broken, or missing accessory components. Restores proper fit and function.