Maytag Dryer Cap Or Cover

The Lint Screen Grille is an OEM part for Whirlpool dryers. It works with the lint screen to capture and collect lint during the drying cycle, preventing it from clogging the vent and ensuring proper airflow.

A bad dryer lint screen grille can be caused by regular wear and tear, accumulation of debris, or accidental damage. If the grille becomes cracked, broken, or warped, it can lead to lint escaping from the lint screen or obstructed airflow.

Symptoms of a bad dryer lint screen grille include:

• Lint escaping from the lint screen area.
• Reduced drying efficiency or longer drying times.
• Visible damage or warping of the grille.
• Excessive lint buildup in the venting system.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Lint Screen Housing Assembly is an OEM part for Whirlpool dryers. It houses the lint screen, which captures lint and debris from the drying cycle, preventing it from clogging the dryer vent and ensuring efficient airflow.

Causes of a bad housing assembly can include cracks or breaks due to frequent handling, wear and tear over time, or accidental impact. A faulty housing can compromise the lint screen's ability to trap lint effectively, leading to potential ventilation issues.

Symptoms of a bad lint screen housing assembly include:

• Lint screen not fitting properly
• Visible cracks or damage to the housing
• Increased lint buildup inside the dryer
• Longer drying times due to restricted airflow

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Inlet Valve is an OEM replacement part for Whirlpool dryers. Located where the water supply line connects, it controls the flow of water into the dryer drum for steam cycles. Precise control is needed to prevent temperature fluctuations or flooding.

Causes of a bad inlet valve can include mineral buildup clogging water pathways, worn diaphragms allowing constant flow, or mechanical linkage issues.

Symptoms of a bad water inlet valve include:

• Steam cycles not activating or producing steam
• The dryer fails to stop water flow and overflowing
• Fault codes displayed relating to water input functions

This OEM replacement part is compatible with brands like Maytag, KitchenAid, and more.

This lint screen grille covers the lint filter opening inside the dryer drum. It supports the lint screen and provides a smooth surface at the opening to prevent snags, restoring proper fit and safe airflow. What it does:

• Supports and aligns the lint screen so it sits flush in the opening
• Shields the blower intake and keeps fabrics from contacting internal parts
• Provides a smooth edge to help prevent clothes from snagging or fraying
• Typical failure signs: cracked or missing grille, broken tabs, lint screen not seating properly, clothes catching near the lint opening

• 1 lint screen grille

• Disconnect power before servicing
• Open the dryer door and remove the screws securing the existing grille
• Lift out the old grille, position the new grille, and secure it with the existing screws
• Reinstall the lint screen and verify it slides smoothly and sits flush

The Lint Screen Door is an OEM replacement part for Whirlpool dryers. It is responsible for covering the lint screen area and protecting the inner components of the dryer drum. The lint screen door allows for easy access to clean out lint buildup after each load.

Over time, the door can suffer from wear and tear due to regular handling or accidental impacts. A faulty lint screen door can lead to improper lint trapping, which might cause airflow issues and potential fire hazards.

Symptoms of a bad lint screen door include:

• Difficulty opening or closing the door smoothly
• Gaps or openings that allow lint to bypass the screen
• Warping or misshapen door that no longer fits properly

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

This replacement door restores a secure close and proper sealing for your appliance. Replacing a damaged or misaligned door helps ensure safe operation and correct latch/switch engagement for reliable everyday use. What it does:

• Provides the closing barrier for the appliance cabinet to maintain proper containment (heat, air, steam, or moisture as designed)
• Aligns with hinges and latch/door switches for correct interlock and operation
• Helps prevent leaks and drafts and protects the interior from damage
• Can address issues such as difficulty closing, visible cracks/dents, poor sealing, or the unit not starting/stopping when the door is moved

• Includes 1 door

• Disconnect power before servicing; also shut off gas or water if applicable
• Support the door during removal/installation; a second person may be needed for larger/heavier doors
• Transfer any reusable hardware (hinge pins, screws, nameplate/trim) from the original as needed
• After installation, verify alignment, latch engagement, and seal/gasket contact; test operation

• Finish, handle style, and configuration are model-specific—ensure the correct match

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This protective cover shields and guides the appliance's water line at the back, helping prevent kinks, abrasion, and vibration. Replacing a damaged or missing cover helps protect the tubing and supports consistent water flow. What it does:

• Protects and routes the water supply tubing to reduce rubbing and wear
• Helps prevent kinks or pinches that can restrict water flow
• Keeps the line secured to minimize vibration and rattling
• Common signs include a cracked/missing cover, exposed/kinked tubing, leaks, or reduced water flow

• 1 water hose cover

• Disconnect power and shut off the water supply before servicing
• Pull the appliance forward for access; remove any screws/clips securing the old cover
• Note the tube routing; install the new cover without pinching the line
• Restore water and power, then check for proper flow and any leaks

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adhesive label replaces a worn, damaged, or missing information label on your appliance so model, serial, and warning details remain readable and the unit stays compliant with safety and service needs. What it does

• Restores legible model/serial/rating and safety information used for service and identification
• Replaces faded or peeled factory-applied adhesive labels
• Helps ensure important operating and safety instructions remain visible
• Improves appearance by covering damaged or discolored label areas

• Clean and dry the mounting surface thoroughly before applying the label
• Peel backing and press firmly, smoothing out air pockets for full adhesion
• Avoid stretching the label during installation; align carefully before contact
• If the label is near electrical components, disconnect power before working in the area