Maytag Dryer Heating Element

This is a dual radiant surface element for compatible glass-ceramic ranges and cooktops. It restores responsive, even heating and lets you choose a smaller inner ring or the full element to match your pan size. What it does:

• Converts electrical energy into radiant heat for the cooking zone
• Dual circuits provide selectable inner-only or full-size heating
• Helps resolve a burner that won't heat or heats only on one ring
• Addresses uneven or intermittent heat and visible hot spots or breaks in the element

• 1 dual radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool before servicing
• Access the element per your model's service procedure; note wire locations before removal
• Handle the element carefully and transfer any mounting brackets/insulators from the original
• After installation, test both inner and outer heat settings for proper operation

Dryer

This genuine heating element restores consistent, controlled heat so your appliance can reach and maintain the proper temperature. Replacing a failed element can resolve no-heat or weak-heat issues and bring performance back to normal.

• Converts electrical energy into heat when powered by the control
• Helps the unit achieve and hold the set temperature during operation
• Typical failure symptoms: no heat, slow or uneven heating, cycles that take longer than normal, visible damage to the element
• May trigger heat-related error codes when failing

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire locations and terminal orientation before removal; transfer any mounting hardware from the original if needed
• Avoid bending or striking the element; handle by the bracket/insulators
• After installation, run a test cycle to check for secure connections

Built for electric dryers that require a 240V heater, this complete heater assembly restores proper heat output. Replace a burned-out element to resolve no-heat or weak-heat complaints and return your dryer to consistent, efficient drying.

• Generates the hot air needed to dry laundry during the cycle
• Typical failure symptoms: drum turns but no heat, longer dry times, or intermittent heating
• Can be checked with a continuity test; a broken or grounded coil indicates replacement is needed
• Factory-style 240V configuration for proper operation on compatible models

• Disconnect power at the breaker before servicing
• Access the heater per your model's service procedure and document wire locations
• Move wires to matching terminals; transfer any attached brackets/sensors from the old assembly if your model uses them
• Clear lint and verify airflow before a test run to confirm proper heating and cycling

This replacement heating element restores proper heat in electric dryers designed with two-level heat. It generates the controlled heat needed for both high and low temperature cycles, helping return normal drying performance.

• Heats the air passing through the drum during drying cycles
• Supports two-level heat so high and low temperature settings work correctly
• Typical symptoms include: no heat, insufficient heat, longer-than-normal dry times, or only one heat setting working
• A visibly broken coil or an open reading on a continuity test indicates failure

• Disconnect power before servicing; dryer circuits carry high voltage
• Handle the element carefully—coils and insulators are fragile; do not stretch or deform the coil
• Note wire locations and ensure tight, clean connections during reassembly
• Clear lint and verify airflow; restricted ventilation or failed thermostats/cutoffs can lead to repeat element failure

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

208 Volts