Maytag Range / Cooktop / Oven Valve

This gas valve controls the flow of gas to a burner, enabling safe ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent flame performance on your gas cooking appliance.

• Opens and closes to start/stop gas flow to a specific burner
• Works with the control knob to modulate flame size
• Helpful when a burner won't light despite spark/ignition present
• Can address issues like inconsistent flame or a knob that's hard to turn

• Disconnect power and shut off the gas supply before servicing
• Match the orientation and connections to the original valve
• Use an approved gas-rated thread sealant on threaded fittings
• After installation, check all joints for leaks with a soap-and-water solution

This gas surface burner valve regulates fuel flow to a cooktop or range burner for safe ignition and smooth flame control. Replace a worn or sticking valve to restore consistent flame adjustment and reliable knob operation.

• Regulates gas to the surface burner; opens/closes as the control knob is turned
• Helps resolve no-flame or no-ignition conditions when sparking is present
• Restores proper flame adjustment from low simmer to full boil
• Addresses stiff, seized, or inconsistent valve action at the knob

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the knob and access the manifold to detach the old valve; note tubing and orientation
• Transfer any mounting clip or fittings from the original valve if required by your model
• After reassembly, check all connections with an approved leak-detection solution and verify burner operation

16K. Mueller.

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This burner valve controls the flow of gas to a single surface burner, restoring proper burner ignition and heat control. It's a direct-replacement gas valve that helps fix intermittent or no-flame burner operation. What it does:

• Regulates gas flow to one surface burner so the burner lights and the flame responds to the control knob.
• Replaces a valve that is stuck, leaking, or not allowing gas through, which can cause a burner to fail to light or produce a weak/unsteady flame.
• Works with pilot/ignition systems to ensure consistent ignition when the knob is turned.
• Helps eliminate clicking or continuous sparking caused by failed gas delivery (when ignition sequence is otherwise OK).

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any work.
• Verify valve orientation and connections match your appliance.
• Use approved fittings and check all gas connections for leaks with a soap solution or gas leak tester after installation.
• Do not attempt repairs if you smell gas; ventilate the area, avoid open flames.

This valve kit repairs the appliance's water/control valve assembly and provides the small mounting screw needed for secure installation. It replaces a worn or damaged valve kit so the appliance can restore proper valve function. What it does:

• Replaces the valve assembly components that control water flow or internal fluid routing
• Helps stop issues caused by a damaged valve kit, such as inconsistent water delivery or valve leakage
• Restores secure mounting with the included screw to prevent loose fittings
• Works as the direct replacement kit specified for the original valve location

• Disconnect power and shut off water supply before starting any repair
• Handle valve components carefully to avoid damaging seals and fittings
• Use basic hand tools; avoid overtightening the mounting screw to prevent stripping

A replacement surface burner valve that controls gas flow to a cooktop burner for consistent flame and heat. Restores proper burner response so burners light and adjust as expected. What it does

• Regulates gas flow to a single surface burner so flame size responds to the control knob
• Helps resolve a burner that won't light or produces little or uneven flame
• Replaces a worn or faulty valve that causes inconsistent temperature during cooking
• Use with the corresponding manifold and control knob assembly for full operation

• One burner valve (surface)

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Inspect connections and fittings for proper sealing; check for leaks after installation with a soap solution
• Handle components carefully to avoid damage to valve ports and threads

The Valve-Gas is an OEM part for Whirlpool gas stoves. It controls the flow of gas from the supply line into the burner tubing, igniters, and flames themselves during the operation of the range top. Precise control of gas flow is critical for safe and efficient cooking performance.

Symptoms of a bad gas valve can include:

• Inability to ignite one or more burners  
• Unstable, intermittent burner flames
• Burners that cannot be turned low enough or click off suddenly 
• Escaping gas odor near the range

Causes of a bad valve may involve wear and tear of internal parts like diaphragms or seals letting in air/gas, corrosion on valve surfaces from gas or moisture, or damage from appliance service/movement over time. 

This Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, Amana, Magic Chef, and select Kenmore models.

This burner valve controls gas flow to a single surface burner, restoring proper heat output and reliable ignition when the valve is functioning. It's the direct replacement part that lets a burner reach its correct flame level. What it does:

• Regulates gas flow to one cooktop burner so the flame responds to knob position
• Enables steady ignition and consistent heat for normal cooking
• Common symptoms it addresses: burner won't light, flame is weak or won't stay lit, or burner only works on certain knob settings
• Designed to match OEM fit and function for straightforward replacement

• Turn off gas supply and electrical power before starting any work
• Use appropriate hand tools; avoid forcing fittings or connections
• After installation, check all gas connections for leaks with a soap solution or approved leak detector

This gas valve controls fuel flow to the range/oven burner, restoring reliable ignition and heat control. Precision operation helps maintain even cooking and safe burner performance when the valve is faulty. What it does:

• Regulates gas flow to the burner assembly so the oven/range heats correctly
• Works with the appliance's safety and ignition systems to enable reliable lighting
• Commonly replaced for symptoms like no heat, intermittent ignition, or gas smell during operation
• Designed as a direct-fit valve for compatible Whirlpool-built ranges using Copreci 16k valves

• Turn off gas supply and disconnect power before attempting service
• Follow the appliance service manual for proper valve removal and gas line reconnection
• Check all fittings for leaks after installation and before returning the appliance to service