Maytag Range / Cooktop / Oven Igniter

• Gas igniter glows, but will not light
• Won't start
• Little to no heat when baking

I watched a video by AppliancePartPros, and it showed the exact problem that I was having as well as what part that I would need for the repair. So I ordered the part which was and oven igniter, that also turned out to be the exact replacement for my old igniter.The part came in the mail in a about 3 days and I was able to install it myself in about 20 minutes give or take, with simple hand tools, then I did a quick test and everything worked fine. THANKS APPLIANCE PARTS PROS FOR ALL OF YOUR... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

The oven would not heat up but the broiler and stove top burners all worked so I replaced the igniter. The part arrived quicker than I expected - one day with regular shipping - and the repair also went much quicker than expected. After accessing the igniter I was able to unplug the plastic modular connection. Instead of pulling the oven out from the wall - which would have been a huge pain - I was able to reach the plug by removing the bottom storage drawer under the oven. From there it was... Read more

• Little to no heat when broiling
• Little to no heat when baking
• Gas igniter glows, but will not light
• Won't start

Replaced the igniter, Simple but there are several points to remember. TURN THE POWER OFF 1) remove the oven door or you will have a hard time reaching the back of the oven. Mine just lifted off. 2) The igniter tip is fragile put a drop cloth over the oven floor in case you drop it even after it is in its holder. 3) The drop cloth will catch screws too if you drop them so they won't fall into the oven. 4) The cable from the oven is very short even after pulling it out from the hole at the back.... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more

• Won't start

Replaced igniter---works great---saved service call. Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

Replaced the oven igniter Whirlpool Part Number WPW10324738. Read more

We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light

Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30! Read more

First I watched the repair video, and then was successful in changing out two of the Ignitor's on the surface Burners, it worked great ! Read more