Maytag Washer Dryer Combo Parts

This drive motor powers the rotating component in your appliance, restoring smooth, reliable motion when the original motor is worn, seized, or noisy. Use it to fix no-rotation issues and inconsistent operation.

• Converts electrical energy into torque to rotate the attached component as designed for your model
• Helps resolve symptoms like no movement, stalling, or slow/intermittent rotation
• Restores consistent, dependable rotation under normal load

• Disconnect power at the breaker before servicing; appliances may contain sharp edges and high-voltage components—use caution
• Note wire/connector orientation and transfer any mounting grommets or brackets from the old motor
• Ensure the driven component turns freely by hand before restoring power
• After installation, run a short functional test to confirm proper rotation

Includes ball bearing, rear bearing, water deflector, hose clamp, spacer, motor isolator, plug & Lip Seal

A replacement latch spring that helps the appliance door latch return and hold securely, restoring reliable door engagement and proper cycle starts. Fits the original latch mechanism and installs quickly for common latch-related issues. What it does:

• Provides tension for the door latch so the strike stays engaged during operation
• Restores proper door closing and helps prevent door from popping open mid-cycle
• Commonly used when the latch feels loose, the door won't stay closed, or cycles won't start
• Works with the appliance's existing latch assembly to return the latch to its resting position

• One spring for the door latch

• High-level replacement: remove access panel or door trim to reach the latch assembly
• Handle spring under tension carefully and wear eye protection to avoid injury
• If other latch components are damaged or worn, replace the entire latch assembly for a reliable repair
• Unplug the appliance or disconnect power before starting any repair

This front baffle grommet cushions and secures a dryer's front baffle to reduce vibration and noise while helping keep the baffle properly positioned during operation. Fits select Whirlpool-built dryers. What it does:

• Cushions the baffle to reduce rattling, knocking or squeaking noises during spin
• Holds the baffle in place to prevent movement or rubbing against the drum
• Helps maintain even drum rotation and prevents premature wear of plastic/metal parts
• Can wear or crack with age, causing noise or loose baffle symptoms

• High-level replacement — remove dryer front or access panel;
• Use proper tools and support panels; keep screws and fasteners organized for reassembly
• Disconnect power (and gas if applicable) before starting work

This exhaust vent extension provides extra duct length to move dryer or hood exhaust farther from the appliance, improving airflow routing and helping reduce backpressure and lint buildup in short-vent installations. What it does:

• Extends the length of an existing exhaust duct to reach a distant vent outlet
• Helps restore proper ventilation when original ducting is too short
• Reduces restricted airflow that can cause longer dry times or excess lint accumulation
• Works as an inline rigid/semirigid extension piece for exhaust systems

• Disconnect power (and gas for gas dryers) before accessing or modifying exhaust connections
• Remove lint and debris from ducting before installing the extension to ensure clear airflow
• Securely fasten with appropriate clamps or foil tape and maintain a smooth, unobstructed path

This drain hose routes wastewater from the appliance to the household drain, helping remove used water after a cycle. It replaces a damaged, kinked or leaking hose to restore proper draining and prevent puddling. What it does:

• Carries discharge water away from the appliance during drain cycles
• Restores proper draining when the original hose is cracked, split or leaking
• Helps prevent backups and standing water inside the appliance
• Works with the appliance's pump and drain system to maintain normal operation

• One replacement drain hose

• Disconnect power and water before starting any work
• Verify hose routing and secure clamps to prevent kinks and leaks
• Inspect and replace any worn clamps or fittings as needed
• After installation, run a short cycle and check for leaks and proper drainage

This connector is an insulated electrical harness terminal that joins appliance wiring to restore a secure electrical connection and help prevent intermittent power or arcing. It's a direct-replacement style used on select Whirlpool appliances. What it does:

• Provides a secure, insulated connection between two wires or a wire and a component terminal.
• Helps stop intermittent power, flickering, or loss of function caused by loose or damaged terminals.
• Reduces risk of arcing and overheating at a compromised connection point.
• Matches OEM fit/shape to maintain proper routing and strain relief where applicable.

• Turn off and unplug the appliance (or shut off breaker) before inspecting or replacing electrical parts.
• Inspect surrounding wiring and terminals for heat or corrosion; replace damaged wiring as needed.
• Use proper crimping or terminal tools and secure strain relief; verify firm, no-play connections before restoring power.

This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:

• Replaces a damaged or bent door hinge to correct misaligned or sagging doors
• Restores smooth hinge movement for easier opening and closing
• Helps the door seal properly to maintain internal temperature and efficiency
• Prevents rubbing or binding that can damage door gasket or cabinet finish

• Disconnect power to the appliance before beginning any repairs to avoid injury
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow for correct alignment and torque
• After installation, check door alignment and gasket contact; adjust as needed

Spesc: #12 pozi - drive

This Torx-head screw set replaces worn, stripped or missing Torx fasteners used throughout the appliance to keep panels and components securely fastened. Restoring proper fasteners reduces vibration and prevents loose parts. What it does:

• Secures control panels, trim pieces or internal components that use Torx-head screws
• Replaces damaged or corroded Torx screws that can cause rattling or misalignment
• Helps restore proper fit and finish after repairs or disassembly
• Uses a Torx drive for a more secure torque transfer than standard Phillips heads

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size Torx driver to avoid stripping the screw head
• Tighten screws snugly but avoid over-torquing to prevent thread or part damage
• Keep removed screws organized and compare to the new set before installation

This hex-head screw secures the bearing insert in place, maintaining correct alignment and stable operation. Replacing a damaged or missing screw restores secure bearing retention and reduces noise or wobble. What it does:

• Holds the bearing insert assembly firmly to prevent movement and misalignment
• Helps stop excessive vibration, noise, or drum wobble caused by a loose bearing insert
• Maintains correct spacing so the bearing and shaft rotate smoothly
• Replaces stripped, rusted, or missing fastening hardware for reliable operation

• Unplug the appliance or disconnect power before beginning any repair
• Use the proper hex driver and size to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can deform the insert or housing
• Inspect the bearing insert and surrounding parts; replace any damaged components for a lasting repair