Parts for Kitchenaid 5KSM185PSBPP5: Motor And Control Unit Parts

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

This chrome speed control lever replaces a worn or broken console lever so you can select dryer or washer speed settings with a secure, finished grip. It restores the original look and control feel on compatible Whirlpool-style consoles. What it does:

• Replaces the front-facing lever used to change speed or cycle options on the control console
• Provides a finished chrome appearance that matches console trim
• Restores a secure grip and positive engagement to prevent slipping or missed selections
• Commonly used when the original lever is cracked, loose, or cosmetically damaged

• Designed for snap-on or screw-retained installation on the console shaft; retain original fasteners
• Turn power off at the breaker or unplug the appliance before servicing
• Handle panels and bezels carefully to avoid scratching the chrome finish

The Control Plate Spring is an OEM part for Whirlpool stand mixers. This spring maintains the proper tension and alignment of the control plate, ensuring the smooth operation and accurate adjustment of the mixer speeds.

Causes of a bad control plate spring can include wear and tear over time, stretching from continuous use, or damage due to overloading the mixer.

Symptoms of a bad control plate spring include:

• Difficulty in adjusting mixer speeds
• Mixer speeds not responding accurately to control adjustments
• Loose or unresponsive control lever
• Unusual noises during speed changes

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Motor Housing Seal is an OEM part for Whirlpool stand mixers. It is designed to create a secure seal around the motor housing, preventing dust, moisture, and other contaminants from entering and damaging the motor. This seal ensures the longevity and optimal performance of the mixer.

Causes of a bad motor housing seal can include general wear and tear over time, exposure to harsh cleaning chemicals, or mechanical stress from frequent use. These factors can lead to the seal deteriorating and losing its effectiveness.

Symptoms of a bad Motor Housing Seal include:

• Visible cracks or splits in the seal
• Dust or debris inside the motor housing
• Reduced performance of the mixer
• Unusual noises or overheating during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Speed Governor is an OEM part for Whirlpool mixers. It regulates the mixer's speed, ensuring consistent performance and preventing the motor from running too fast or too slow.

Over time, the speed governor can wear out or become damaged due to regular use or mechanical issues within the mixer. Exposure to moisture or electrical problems can also cause malfunctions.

Symptoms of a bad Speed Governor include:

• Inconsistent mixing speeds
• Mixer running too fast or too slow
• Mixer not starting or stopping unexpectedly
• Irregular performance during mixing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw is a direct-fit fastener used to secure appliance panels and components, restoring proper fit and reducing movement. Ideal when original screws are stripped, missing, or damaged. What it does:

• Secures panels, trim, brackets, and other serviceable components to prevent rattling or misalignment
• Matches original fastener form for correct fit and reliable function
• Helps restore proper clearance and component alignment after repair
• Safe, general-purpose replacement for common appliance fastening needs

• Turn off power and disconnect the appliance before accessing internal components
• Use the correct screwdriver or bit; avoid overtightening to prevent thread or part damage
• Keep hardware and small parts away from children and pets

The Speed Control Plate is an OEM part for Whirlpool stand mixers. This part regulates the speed at which the mixer operates, ensuring that it can accurately adjust to the desired setting for a wide range of mixing tasks.

Over time, the speed control plate can wear out or become damaged due to regular use, leading to issues such as the mixer not maintaining the set speed, operating too fast or too slow, or not adjusting speeds at all.

Symptoms of a bad Speed Control Plate include:

• The mixer fails to change speeds or adjust accurately
• The appliance operates at an incorrect speed regardless of the setting
• The mixer only works at one speed or does not work at all
• Unpredictable speed changes during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement power cord restores electrical connection to your appliance so it can receive power safely and reliably. Designed as a direct-fit replacement when the original cord is damaged or worn. What it does:

• Replaces a damaged or frayed power cord to restore safe power delivery
• Allows the appliance to power on and operate normally once properly installed
• Reduces risk of electrical arcing or shorts from cracked insulation or exposed wiring
• Helps stop intermittent power loss caused by a faulty cord or connector

• Disconnect the appliance from power before removing the old cord or installing this one.
• Inspect terminals and strain relief; route the cord to avoid pinch points and sharp edges.
• Tighten all connections securely and replace any damaged strain relief or covers.