Parts for Kitchenaid KFXS25RYBL2: 04 - Motor And Ice Container Parts

The Water Filter is an OEM part for Whirlpool refrigerators. It is designed to filter and purify the water for your refrigerator, ensuring clean and fresh drinking water and ice.

A bad refrigerator water filter can be caused by regular use and the buildup of contaminants over time. It may also become less effective if not replaced according to the manufacturer's recommended schedule.

Symptoms of a bad refrigerator water filter include:

• A decrease in water flow or water pressure.
• An unpleasant taste or odor in the water.
• The presence of particles or sediment in the water.
• Cloudy or discolored ice cubes.

If you notice any of these signs or if it has been more than six months since your last filter replacement, it's time to replace the refrigerator water filter with this genuine OEM part. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Ice Container Assembly is an OEM component for Whirlpool refrigerators. It is the bin that collects and stores ice produced by the ice maker. With its precise design and durable construction, the ice container allows ice cubes to easily drop down through the chute from the ice maker.

Causes of a bad ice container assembly can include cracks or broken parts that prevent proper operation. Over many uses, normal wear and tear may compromise its ability to effectively store and retain ice.

Symptoms of a bad ice container assembly include:

• Ice cubes dropping outside of the container and accumulating elsewhere  
• Difficulty removing cubes from the container
• Cracks or openings that compromise insulation and cause premature melting

This replacement is also compatible with Kenmore, KitchenAid, and select Maytag models.

This fan scroll is the blower housing that directs airflow from the blower motor to the appliance's ducts, helping maintain proper circulation. It replaces a damaged or warped housing to restore efficient airflow and reduce noise. What it does:

• Channels air from the blower motor into the appliance air path for cooling or venting.
• Helps maintain consistent temperatures and airflow for proper operation.
• Can reduce vibration or rubbing noises caused by a cracked or deformed housing.
• Supports the blower motor assembly and seals the motor-to-duct interface.

• One fan scroll / blower housing.

• Disconnect power to the appliance before starting any repair.
• Installation may require removal of the blower motor and nearby panels; handle motor and impeller carefully.
• Inspect and reuse or replace any required mounting hardware, gaskets, or seals as needed—only what explicitly ships is included.
• If you hear unusual noises after installation, recheck alignment and clearance between the impeller and the scroll.

The Motor-Evaporator is an OEM part for Whirlpool refrigerators. It powers the cooling system responsible for maintaining proper internal temperatures. The evaporator motor functions by circulating refrigerant through coils located behind the refrigerator liner. 

Symptoms of a bad motor evaporator include:

• Fluctuating interior temperatures
• Inability to achieve desired cooling levels
• Ice buildup caused by inefficient airflow
• Unusual noises or vibrations from the cooling system

Causes of failure relate to wear and tear of internal motor components over time. Replacement ensures optimized temperature performance through consistent operation of refrigerant circulation.

This OEM Whirlpool part is also compatible with Kenmore, Maytag, Jenn-Air, and some KitchenAid models.

This blower wheel moves air through the appliance's ventilation system so clothes dry evenly and components stay cool. It restores proper airflow to improve drying performance and reduce overheating risk. What it does:

• Spins to circulate air through the drum and exhaust vent for efficient drying
• Replaces a damaged or broken wheel that can cause reduced airflow and long dry times
• Stops abnormal noises from a cracked or out-of-balance impeller
• Helps prevent overheating caused by restricted or insufficient airflow

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect the mounting shaft, housing, and fasteners; replace any damaged hardware
• Ensure correct wheel orientation and secure fit to avoid vibration or rubbing

A small rubber mounting grommet that cushions and protects components where they pass through or sit against a chassis or housing. Replaces worn or damaged grommets to reduce vibration and keep parts properly positioned. What it does:

• Provides a vibration-dampening cushion for mounted parts or wiring
• Protects wires, hoses, and metal edges from abrasion at pass-throughs
• Helps keep components aligned and secure during operation
• Worn or cracked grommets can cause rattling, rubbing noises, or movement of parts

• One replacement rubber grommet

• Disconnect power before starting any repair
• Access may require removing panels or trim—refer to your model's service manual or diagram
• Inspect surrounding parts and replace any additional worn fasteners or seals as needed
• Use appropriate tools and take care not to damage wiring or components when installing

This ice box divider fits inside the refrigerator's ice container to separate sections and guide ice to the dispenser. Replacing a cracked or missing divider helps prevent jams and keeps cubed or crushed ice dispensing the way it should.

• Separates the ice bin interior and channels ice toward the auger/dispenser path
• Helps maintain proper cubed/crushed ice selection and flow
• Reduces spillover and clumping that can block dispensing
• Common symptoms of failure: poor or no ice dispense, inconsistent cubed/crushed output, or ice overflowing inside the bin

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin, empty remaining ice, and locate the internal divider
• Transfer any reusable hardware/clips and install the new divider in the same orientation
• Reinstall the bin, restore power, and test both cubed and crushed dispense

This gasket for the damper assembly provides a replacement seal that helps keep compartments properly isolated and reduces air leakage. Replacing a worn gasket restores more consistent airflow and supports stable internal temperatures. What it does:

• Seals the damper opening to reduce unwanted air transfer between compartments.
• Helps the damper close and regulate airflow for more consistent temperature control.
• Common symptoms of a failing gasket: temperature swings, frost or moisture buildup, and noisy or improperly closing damper.
• Restoring a proper seal can improve cooling consistency and help avoid overworking the compressor.

• Disconnect power to the appliance before attempting service.
• Remove interior items and any trim panels needed for damper access; use gentle prying to avoid damage.
• Seat the new gasket fully into the damper groove and verify smooth damper movement before replacing panels and contents.

The Auger Motor is an OEM part for Frigidaire refrigerators. This motor powers the auger in the refrigerator's ice maker unit. The auger rotates during ice-making, ejecting ice from the mold and depositing cubes into the storage bin.  

Causes of a bad auger motor can include wear and tear over time from continuous use, or damage from unbalanced ice molds or debris buildup.

Symptoms of a bad auger motor include:

• Ice maker not producing ice or producing ice inconsistently  
• Ice cubes jammed or frozen together in the storage bin
• Loud buzzing or grinding noises coming from the ice maker area
• Inability to eject ice properly into the storage bin

Replacing this OEM Frigidaire auger motor helps ensure consistent, reliable ice production. This replacement part is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Damper Control Assembly is an OEM part for Whirlpool refrigerators. This component regulates the flow of cold air from the freezer compartment to the refrigerator compartment, ensuring consistent and optimal temperatures throughout the appliance. It plays a critical role in maintaining the balance between freezer and refrigerator temperatures.

Common causes of a bad damper control assembly include electrical malfunctions, physical damage to the damper, or wear and tear from regular use. Over time, the motor or the damper flap can fail, leading to improper air regulation.

Symptoms of a bad damper control assembly include:

• Inconsistent temperatures between the freezer and refrigerator compartments
• The refrigerator being too warm or too cold
• Frost buildup in the refrigerator compartment
• The damper making unusual noises or not moving as it should

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This ice dispenser solenoid assembly engages the dispenser mechanism to switch between crushed and cubed ice. A worn or failed solenoid can prevent the selector from changing modes or stop ice from dispensing smoothly.

• Actuates the ice bucket/crusher selector to allow cubed or crushed ice
• Failure may cause only one ice option to work, no change between modes, or intermittent dispensing
• Can resolve loud clicking/buzzing from the dispenser area when switching options
• Helps restore proper ice dispensing performance

• Disconnect power before servicing the dispenser area
• Access is typically through the freezer door dispenser chute/ice bucket area
• Note actuator linkage orientation during removal to ensure correct reassembly
• After installation, test both crushed and cubed selections

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

This mounting bracket secures internal panels and components to restore proper alignment and support. It replaces a worn or broken bracket to reduce rattling and keep parts correctly positioned for safe operation. What it does:

• Provides a stable attachment point for panels or assemblies
• Stops movement that can cause rattling, noise, or misalignment
• Restores proper fit between connected parts after damage or wear
• Helps prevent strain on adjacent components that can lead to failure

• High-level replacement: remove nearby panels or fasteners to access and swap the bracket
• Use correct fasteners and torque; replace any damaged clips or screws
• Disconnect power before working on electrical appliances and follow safety procedures