Norge Parts

This access cover protects and conceals internal appliance components, helping keep wiring and controls shielded from dirt and accidental contact. It restores the appliance's finished appearance after service. What it does

• Covers and protects internal electrical and mechanical parts from debris and accidental contact
• Helps maintain proper airflow pathways and component positioning where applicable
• Prevents loose items from entering service areas that could cause damage or noise
• Useful when replacing or servicing internal parts to restore the appliance's exterior finish

• One access cover as shown

• Disconnect power (unplug or shut off breaker) before installation to avoid shock
• Use appropriate hand tools (screwdriver or nut driver) and keep fasteners for reassembly
• Handle edges carefully — metal or plastic edges may be sharp

This overload is a thermal protection device that mounts on the motor/compressor and opens the circuit when excessive heat or current is detected. Replacing a weak or failed overload helps restore safe startup and protects the windings from damage. What it does:

• Monitors motor/compressor temperature and current draw
• Interrupts power on overheat/overload to prevent damage
• Aids troubleshooting of start/run issues when paired with the start device
• Common symptoms: hums then clicks off, won't start, intermittent shutdown, frequent tripping

• 1 thermal overload protector

• Disconnect power before servicing; allow components to cool
• Access the terminal area on the motor/compressor; remove any cover
• Note/photograph wire positions; transfer wires and fully seat the new overload on the correct terminal
• Inspect the start relay, capacitor, and terminals for heat damage; replace any compromised parts

This O-ring creates a watertight seal in your dishwasher's wash or drain system, helping prevent leaks and maintain proper water pressure. Replace a brittle, flattened, or damaged ring to restore a reliable, leak-free connection.

• Provides a watertight seal between mating parts such as pump housings, fittings, or hose joints
• Helps stop drips and seepage caused by a worn or deformed seal
• Common symptoms: water under the unit, moisture around pump/tubing connections, or leaks after reassembly
• Replace if the old ring is cracked, cut, flattened, or hardened

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water
• Clean the groove and mating surfaces; lightly moisten or use a manufacturer-approved lubricant to help the ring seat without pinching
• Seat evenly, reassemble without overtightening, and run a short test cycle to check for leaks

30-inch door handle replacement that restores a secure grip and the door's appearance. Replaces cracked, loose, or broken handles so you can open and close the appliance door safely and with confidence. What it does:

• Provides a comfortable, secure grip for opening and closing 30-inch appliance doors.
• Replaces damaged, loose or broken handles to restore normal door operation and appearance.
• Designed as a direct replacement for the factory door handle mounting pattern.
• Helps prevent accidental drops or slippage when opening a hot or heavy oven/range door.

• Always disconnect power to the appliance and allow it to cool before beginning any repair.
• Support the door during removal and installation; have a helper if the door is heavy or awkward.
• Use the correct screwdriver or bit for the mounting screws and keep removed hardware organized for reinstallation.

This replacement white infinite-switch knob restores precise temperature control for electric surface burners. It fits standard shaft-style infinite switches and provides a simple, visible control for cooktop heating adjustments. What it does:

• Replaces a worn, cracked, or missing infinite-switch control knob to regain reliable burner control
• Slides onto the stove or range infinite switch shaft to adjust heat settings smoothly
• Helps resolve symptoms like loose spinning knobs, difficulty selecting heat levels, or missing pointer alignment
• Matches original appearance for a clean, factory-look control panel

• One white infinite-switch control knob

• Remove power to the appliance before servicing to avoid risk of shock
• Pull the old knob straight off the switch shaft; push the new knob fully onto the shaft until seated
• No special tools typically required;

Kit includes four knobs.