Norge Spring Parts

The Suspension Spring is an OEM part for Whirlpool washing machines. This spring plays a vital role in supporting the washer tub, helping to absorb shocks and vibrations during the washing and spinning cycles, ensuring smooth and stable operation. Can also use Spring Kit (6) part number 12002773

Causes of a bad suspension spring can include wear and tear over time, excessive loads that overstress the spring, or corrosion and rust that weaken the spring’s integrity. Damage due to improper handling or installation can also affect its performance.

Symptoms of a bad suspension spring include:

• Excessive shaking or vibrating of the washing machine during operation
• The washer tub being off-balance
• Loud banging or thumping noises during the spin cycle
• The washing machine moving or "walking" during use

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Motor Spring is an OEM replacement part for Whirlpool top-loading washing machines. This spring applies proper tension to the agitator assembly during wash cycles.

Causes of a bad motor spring can include damage from unintended impacts or fatigue after extended use. Over time, constant movement may cause the spring to weaken.

Symptoms of a bad motor spring include:

• Inadequate cleaning as clothes don't tumble vigorously  
• Excessive noise or vibration from the off-balance agitator 
• Stalling or failure of the agitator to rotate fully

This OEM Whirlpool replacement is also compatible with some Kenmore, Admiral, Estate, and Roper top-load washer models as well. 

The Door Spring is an OEM part for Whirlpool dishwashers. This part allows the smooth and controlled operation of the dishwasher door. The spring helps balance the weight of the door, allowing it to open and close effortlessly without slamming shut.

Causes of a bad door spring can include wear and tear from repeated use, corrosion or rust, and breakage due to excessive force or mishandling.

Symptoms of a bad door spring include:

• The dishwasher door dropping quickly or not staying open
• Difficulty in opening or closing the door
• Unusual noises when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This oven door spring restores the door's counterbalance so it opens smoothly and closes firmly. Replacing a fatigued spring helps prevent heat loss and supports consistent baking by ensuring the door seals properly. What it does:

• Provides tension to counterbalance the oven door through the hinge mechanism
• Helps the door close fully against the gasket to retain heat
• Restores smooth, controlled opening and closing action
• Common symptoms of a worn spring: door drops or feels heavy, won't stay closed, heat escaping/uneven temperatures

• One oven door spring

• Disconnect electrical power; turn off gas supply to the range if applicable
• Springs and hinges are under tension—support the door/hinge and use caution
• Note spring hook positions/orientation before removal; reinstall in the same locations
• After replacement, verify the door closes fully and the seal is even

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This idler spring maintains proper tension on the dryer drum belt by keeping the idler pulley engaged. Replacing a weak or broken spring restores consistent drum rotation and helps prevent belt slippage and squealing during operation.

• Maintains belt tension by pulling the idler arm/pulley against the drum belt
• Helps the motor start and keep the drum turning smoothly
• Reduces belt slippage that can cause squealing or chirping
• Common symptoms of a failed spring: drum won't turn or turns intermittently; belt comes off or feels loose; loud squeal from idler area

• Disconnect power; for gas dryers, shut off the gas supply
• Access the idler assembly; relieve belt tension and note belt/spring routing before removal
• Attach the new spring to the same holes/orientation on the idler arm and base; verify belt path
• Rotate the drum by hand to confirm alignment and tension before reassembly