Parts for Electrolux EI30BM6CPSC: Oven,Cabinet Parts

The Wave Guide Cover is an OEM part for Frigidaire microwaves. The cover prevents food particles and moisture from entering the wave guide, helping to maintain the efficiency and safety of the microwave.

Causes of a bad wave guide cover can include exposure to high heat, splatters from food and liquids, or regular wear and tear. 

Symptoms of a bad wave guide cover include:

• Sparks or arcing inside the microwave
• Uneven cooking or heating
• Visible burns, cracks, or discoloration on the cover
• Noise or rattling sounds during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This base plate is the lower cabinet support that restores structural stability and covers the appliance underside for a finished appearance. It helps protect internal components and maintain proper airflow under the unit. What it does:

• Provides structural support for the appliance's lower cabinet and toe area
• Secures and protects internal components located under the unit from debris and accidental contact
• Helps maintain intended airflow and clearance beneath the appliance
• Restores cosmetic appearance where the original base plate is damaged or missing

• One base plate

• Disconnect power to the appliance before starting any work
• Remove the toe grille or access panel to reach base plate mounting points
• Use basic hand tools to remove/replace screws; align plate before tightening

This replacement capacitor restores proper motor start and run performance for compatible refrigerators. It supports compressor startup and stable operation to help maintain cooling when the original capacitor fails. What it does:

• Provides the electrical boost needed to start and run the compressor motor
• Helps prevent slow starts, humming, or repeated restarting associated with a failing capacitor
• Enables stable motor operation during normal refrigerator cycles
• Commonly replaced when the compressor struggles to start or the fridge loses cooling

• One capacitor

• Disconnect power to the appliance before beginning any service
• Capacitors can hold a charge—discharge safely
• Inspect wiring and mounting before installing; ensure correct terminal connections

Replacement electrical diode for Frigidaire refrigerators that directs current flow to protect control circuitry and help defrost and compressor systems operate correctly. Installs quickly to restore proper electrical function when a diode fails. What it does:

• Allows electrical current to flow in only one direction to protect sensitive control and compressor circuits.
• Prevents backfeed that can damage control boards or other components.
• Common symptom: intermittent or no compressor/defrost operation.
• Other symptoms: blown fuses, tripped breakers, or erratic electrical behavior in the appliance.

• Disconnect power to the appliance before beginning any service.
• Handle electrical connections carefully; use insulated tools and avoid touching live terminals.
• Confirm connector fit and orientation before finalizing installation.

This Fuse is an OEM part for Frigidaire microwaves. It's a critical safety component designed to protect the microwave from electrical overload by breaking the circuit if the current is too high. This fuse is specifically tailored to fit and function properly with Frigidaire microwave models, ensuring safety and reliability.

Fuses in microwaves can blow due to power surges, electrical faults within the appliance, or overheating caused by restricted airflow or malfunctioning components. A blown fuse prevents the microwave from operating as a safeguard against potential electrical damage or fire hazards.

Symptoms of a blown fuse include:

• The microwave suddenly stops working and doesn't turn on.
• No response from the microwave's control panel or display.
• The microwave is completely unresponsive, even when the door is opened or closed.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This replacement lamp restores clear, reliable lighting so you can see food and monitor cooking at a glance. Install a new bulb when the original is burned out, flickers, or the glass capsule is darkened or damaged.

• Provides illumination for the appliance interior or work area, depending on model
• Typical symptoms: no light when the door opens or light button is pressed
• Flicker or work intermittently before failing completely
• Visible damage or dark, cloudy glass indicates the bulb has failed

• Disconnect power to the appliance before servicing and allow the lamp area to cool
• Access varies by model; remove the lens/cover or service panel per your unit's documentation
• Handle the bulb by the base; if halogen capsule style, avoid touching the glass
• Replace only with the lamp type and wattage specified for your model

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

This thermostat is a temperature-sensing switch used in select appliances to control operation or provide over-temperature protection. It opens or closes the circuit at a calibrated point to help maintain proper, consistent performance. What it does

• Senses temperature at its mounting/location and switches contacts at a set point
• Regulates cycling of the system or ends a heating/cooling/defrost event as designed
• Helps prevent overheating or overcooling conditions and protects components
• Supports stable, reliable operation when the original thermostat fails

• Runs continuously or won't cycle off
• Shuts off too soon or won't turn on
• Inconsistent temperature (too warm/too cold)
• Erratic cycling or failure to maintain set temperature

• 1 thermostat

• Disconnect power before servicing; allow any hot surfaces to cool
• Note wire positions; move leads one at a time to the new thermostat
• Mount in the original location and orientation; ensure firm contact/fit
• Route any sensing bulb/capillary exactly like the original; avoid kinks

This mechanical thermostat controls refrigerator temperature by sensing evaporator or cabinet temperature and switching the compressor and fans on and off. Replaces a worn or faulty control to help restore consistent cooling and temperature regulation. What it does

• Senses temperature and closes/open circuit to run the compressor and cooling fans
• Helps maintain set temperature by cycling refrigeration system components
• Commonly linked to symptoms like warm or fluctuating temperatures, compressor not running, or continuous running
• Works as the control point for user temperature settings

• One thermostat

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Access may require removing interior panels or control housing
• Handle sensing bulb and capillary tube carefully to avoid kinks or damage

The Thermostat is an OEM part for Frigidaire microwaves. The thermostat accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

The Thermostat is an OEM part for Frigidaire microwaves. Situated near the top of the microwave cavity, it accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

This capacitor helps the refrigerator compressor start and run smoothly, restoring reliable motor operation and improving cooling performance when the original capacitor fails. It's a direct-replacement electrical component used on compatible Frigidaire appliances. What it does:

• Supplies the brief electrical boost the compressor motor needs to start
• Supports continuous motor operation to maintain consistent cooling
• Commonly linked to symptoms such as the compressor struggling to start, loud humming, or reduced cooling
• Helps prevent hard starts that can lead to overheating or repeated cycle failures

• One capacitor

• Disconnect power to the appliance before service to avoid electric shock
• Capacitors can hold a charge—discharge safely before touching terminals
• Verify terminal connections match the original and secure all wiring after replacement

This evaporator fan assembly circulates cold air through the freezer and refrigerator compartments to help maintain even temperatures and proper cooling. Replaces a worn or failed fan to restore airflow. What it does:

• Spins to move cold air across the evaporator coil and into the appliance interior
• Commonly linked to symptoms like unusual noise, weak cooling, or no airflow in compartments
• Helps prevent frost build-up by maintaining steady airflow over the coil
• Works with the appliance's evaporator motor circuit and fan housing

• One evaporator fan assembly

• Disconnect power to the appliance before beginning any work
• Access may require removing interior panels or the evaporator cover; follow your model's service instructions
• Handle the fan blades and motor carefully to avoid damage; avoid contact with sharp sheet metal and edges
• Test the fan operation after reassembly and restore all panels and fasteners

The Latch Hook is an OEM replacement part for Frigidaire microwaves. It is an internal component that helps securely latch and lock the microwave door during operation. The latch hook works with the door handle mechanism to ensure the door is properly fastened to prevent leaks of microwave energy and for safety. 

Causes of a bad latch hook can include wear and tear over time, damage from repeated use of the door latch, or issues with the latch hook spring or connecting components. 

Symptoms of a bad latch hook include:

• The microwave door not closing or latching securely  
• Difficulty closing or popping open the door during a cycle
• Leaks of microwave energy from around the door seals
• Error codes related to door-latching problems

This OEM Frigidaire replacement part is also compatible with Electrolux, Westinghouse, and Kelvinator microwaves. 

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

The Door Switch is an OEM part for Frigidaire microwaves, designed to ensure the appliance operates safely by signaling when the door is securely closed. This switch is critical for preventing the microwave from running if the door is open, a key safety feature that protects users from exposure to microwave radiation.

Causes of a bad Door Switch can include mechanical failure due to normal wear and tear from repeated opening and closing of the microwave door. 

Symptoms of a bad Door Switch include:

• The microwave not starting or heating when the door is closed.
• The appliance continuing to operate when the door is opened.
• Intermittent operation or sudden stopping during use.
• Displaying error messages related to the door or switches.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water filter cartridge replaces the refrigerator's inline/slot-style filter to help reduce taste and odor from your drinking and ice water. It restores filtered water flow and helps keep dispensed water clear and fresh. What it does:

• Removes common impurities that affect water taste and odor
• Helps reduce particulates and sediment in dispensed water
• Restores proper filtered water flow when a clogged/expired filter causes slow flow
• Supports clearer, better-tasting ice and drinking water

• One water filter cartridge

• Turn off the water supply and dispense any remaining water before removing the old filter
• Follow the refrigerator manufacturer's push/pull or twist-release procedure for removal and installation
• After installing, flush several quarts of water through the dispenser to clear air and initial carbon fines
• Replace per the refrigerator manufacturer's recommended schedule or when filter performance declines

This mounting kit secures appliance components in place to restore safe, stable installation and alignment. It provides the brackets and fasteners needed to mount the associated assembly and prevent shifting or rattling during use. What it does:

• Provides the brackets and hardware that hold an appliance assembly securely in position
• Restores proper alignment to reduce vibration, noise, and movement
• Replaces worn or missing mounting hardware that can cause loose panels or components
• Helps ensure connected parts stay fixed for safe, reliable operation

• Turn off and disconnect power to the appliance before attempting any repairs
• Keep all fasteners tight and verify alignment after installation
• If additional parts are missing or damaged, stop and source the correct replacement components before finishing

This Filter is an OEM part for Frigidaire microwaves. It captures grease and other particles from the air during cooking, helping to prevent buildup inside the microwave and in the kitchen's ventilation system.

Over time, filters can become clogged with grease and debris, leading to reduced effectiveness and potential issues with the microwave's performance. Common causes for a filter's deterioration include regular use, especially with high-grease foods, and lack of regular cleaning or maintenance.

Symptoms of a bad filter include:

• Noticeable grease buildup on the filter.
• Reduced effectiveness in venting smoke or odors.
• The microwave becomes louder during operation.
• Decreased efficiency in cooking, particularly with foods that produce a lot of steam or smoke.
• An unpleasant odor emanating from the microwave during or after use.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This genuine connector restores a secure electrical link in your appliance's wiring harness to help re-establish reliable power or signal transfer. It replaces a damaged or corroded connector for safer, more consistent operation. What it does

• Joins wiring within the appliance harness to maintain electrical continuity
• Restores power or control signals to the attached component when a faulty connector causes loss of function
• Helps prevent intermittent connections, arcing, and heat build-up from loose or corroded terminals
• Works where a direct plug-in or crimp-style connection is required by the OEM

• One connector as shown

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing electrical parts
• Verify connector orientation and terminal type match the wiring harness before installation
• Use proper crimping tools or OEM-recommended connector methods; avoid twisting or soldering unless specified by the manufacturer
• If wiring is damaged, repair or replace the harness section per OEM guidance

This evaporator fan assembly circulates cold air through the freezer/fridge compartment to maintain even temperatures and proper cooling. Replacing a failed fan restores airflow and helps prevent frost buildup and temperature problems. What it does:

• Moves cold air across the evaporator and throughout compartments for consistent cooling
• Allows the refrigerator to reach and hold set temperatures by maintaining airflow
• Commonly replaced when the fan is noisy, wobbly, or fails to run
• Can reduce frost/ice buildup caused by restricted airflow

• Disconnect power before beginning any repair to avoid shock or injury
• Access requires removing interior panels or evaporator cover; handle sharp sheet metal and evaporator fins with care
• Verify fan direction and secure mounting; ensure wiring connectors are fully seated
• Test operation after reassembly and restore all panels for proper airflow

This drive belt wraps around the dryer drum and motor pulley to turn the drum and tumble clothes. Replacing a worn or broken belt restores normal drum rotation for even drying and quieter operation. What it does:

• Transfers motor power to the drum so it spins during the dry cycle
• Worn, glazed, or broken belts can cause the drum to stop turning or to slip
• A damaged belt may create squealing or rubbing noises during operation
• Restoring belt function helps return normal tumbling and consistent drying

• One replacement dryer drive (drum) belt

• Disconnect power to the dryer before any service to avoid shock or injury
• Access the drum per your model's service instructions (top/front/remove panels as required)
• Route the belt around the drum and pulleys following the OEM belt path; ensure proper tension
• Inspect drum rollers, idler pulley, and motor pulley while servicing and replace if worn

The Coupler is an OEM part for Frigidaire microwaves. It connects the microwave glass tray to the rotating turntable shaft inside the microwave. The coupler allows for the stable and secure rotation of the glass tray when in use, ensuring even cooking and heating.

Causes of a bad coupler can include wear and tear over time if utilized excessively, as well as damage due to impact or stress placed on the coupler during mishandling or cleaning of the tray.

Symptoms of a bad coupler include:

• The glass tray not spinning or rotating properly during cooking
• Excessive shaking or vibration of the tray
• Detachment or separation of the tray from the turntable shaft
• Leakage or drips occurring near the tray connection point

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Rotating Ring is an OEM part for Frigidaire microwaves. It supports and rotates the glass tray during the cooking process for even heating of your food.

A bad rotating ring can be caused by wear and tear, damage, or improper alignment. Signs of a faulty rotating ring include the glass tray not rotating or turning unevenly, strange noises during operation, or the tray falling off the ring.

Symptoms of a bad rotating ring can include:

• The glass tray not rotating
• Noises during operation
• The tray not fitting securely in place

Replace your damaged or malfunctioning rotating ring with this genuine OEM part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Glass Turntable Plate is an OEM part for Frigidaire microwaves. As the surface food rests upon during cooking, it features heat-resistant tempered glass construction suitable for high-power microwave usage. 

Causes of damage can include cracking or splitting from thermal shock of sudden temperature changes during repeated heating and cooling cycles. Improper cleaning methods using harsh chemicals may also degrade protective coatings.

Symptoms of a faulty glass plate involve: 

• Cracks or chips exposing sharp edges presenting a hazard
• Denting or warping preventing level rotation inside the cavity
• Staining or clouding compromising visibility of cooking foods

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models.

This fan blade mounts to the refrigerator fan motor to move air through the appliance for proper cooling and temperature circulation. Replaces a worn or damaged blade to restore airflow and improve cooling efficiency. What it does:

• Spins on the fan motor to circulate air across the evaporator or condenser coils
• Restores proper airflow when a cracked or broken blade causes reduced cooling
• Helps stop vibration or rattling caused by bent or missing blades
• Can reduce motor strain from an imbalanced or damaged blade

• Disconnect power to the appliance before starting any repair
• Remove access panels and fan shroud to reach the blade; keep track of mounting hardware
• Replace carefully to avoid bending the blade; ensure correct orientation on the motor shaft

This replacement motor restores movement to the appliance's fan or drive assembly so air or components circulate properly for normal operation. It fits original mounting locations and connects to existing wiring for a direct swap. What it does

• Drives the fan or rotating assembly to circulate air or operate a driven component
• Restores normal airflow or mechanical rotation when the original motor fails
• Commonly used when you have loud motor noise, no motor movement, or intermittent operation
• Helps resolve related issues like poor cooling or reduced airflow caused by a stalled motor

• One replacement motor as shown

• Turn power to the appliance off at the breaker or unplug before servicing
• Verify wiring colors and connector fit before disconnecting; replace one wire at a time if needed
• Handle carefully to avoid damaging the shaft or mounting tabs; follow OEM instructions for mounting torque

This replacement shaft transmits rotation between components within the targeted assembly. It restores proper alignment and smooth motion when the original shaft is worn, bent, or stripped, helping the appliance operate reliably again.

• Transfers rotational force between mating components in the mechanism
• Maintains alignment and support for rotating parts
• Ensures secure engagement with the hub/gear to prevent slipping
• Worn or bent shafts can cause wobbling, grinding noises, slipping, or intermittent operation

• Disconnect power (and water supply if applicable) before servicing
• Access the assembly and note the shaft's orientation and any spacers, clips, or washers
• Transfer any reusable hardware from the old shaft and seat the new shaft fully
• Verify smooth rotation by hand before reassembly and testing

This fan blade circulates cold air across the evaporator to help maintain even refrigerator/freezer temperatures and efficient cooling. Replacing a damaged or warped blade restores proper airflow and reduces unusual noise. What it does:

• Moves air across the evaporator coil so the appliance can cool evenly
• Helps prevent hot spots and frost buildup caused by poor airflow
• Can cause loud noise, reduced cooling, or a warm compartment when worn or broken
• Works with the evaporator/fan motor assembly to keep temperatures stable

• One fan blade

• Disconnect power before accessing evaporator compartment or fan assembly
• Handle blade carefully to avoid bending the fins; a bent blade causes vibration and noise
• May require removing evaporator cover or fan shroud; keep track of any screws or clips
• If motor is noisy or blade clearance is tight, inspect/replace motor or mounting hardware as needed

The Vent Damper is an OEM part for Frigidaire microwaves. It is designed to control the flow of air through the microwave’s ventilation system, ensuring proper ventilation during operation. This component helps to prevent the backflow of air, keeping the microwave's interior and its surroundings free from unwanted odors and heat.

Causes of a bad vent damper can include wear and tear over time, accumulation of grease or debris, or damage from external impact. 

Symptoms of a bad vent damper include:

• Poor ventilation
• Unusual odors lingering around the microwave
• Excessive heat buildup
• Increased noise during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Damper is an OEM part for Frigidaire microwaves. This part regulates airflow within the microwave, ensuring that steam and odors are properly vented out during cooking.

Causes of a bad damper can include wear and tear over time, buildup of grease and debris, or damage from high temperatures.  

Symptoms of a bad Damper include:

• Poor ventilation during cooking, leading to lingering odors and steam
• The microwave overheating or not ventilating properly
• Unusual noises coming from the damper area
• The damper not opening or closing as it should

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Mounting Bracket is an OEM part for Frigidaire microwaves. This part securely attaches the microwave to the wall or cabinetry. This bracket is designed to ensure that your microwave is mounted safely and remains stable during operation, preventing any potential movement that could lead to damage or operational issues. 

Causes of a bad Mounting Bracket can include physical damage from improper installation or accidents, wear and tear over time that weakens the bracket's integrity, and corrosion due to exposure to moisture or kitchen vapors, which can compromise its strength and stability.

Symptoms of a bad Mounting Bracket include:

• The microwave tilting or sagging
• Unusual vibrations or noise during operation, indicating that the microwave is not securely fastened
• Visible damage or rust on the bracket itself, which could weaken its support

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged