Parts for Ge SCB1000KCC01: 03 - Oven Cavity Parts

This door switch access cover replaces the plastic access panel that protects and secures the door latch/switch assembly behind the appliance door. It restores a finished appearance and helps keep the switch area safe and stable. What it does:

• Covers and secures the door switch area to prevent debris contact and accidental interference
• Helps maintain proper alignment of the door switch and latch components
• Stops light drafts and reduces rattles around the door switch opening
• Common symptom: cracked, broken, or missing cover causing loose switch or exposed switch components

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the door inner panel or trim as needed to access the switch area; retain fasteners for reassembly
• Align cover over the switch opening and secure with the original screws/clips; do not overtighten
• If any switch or latch parts are damaged, inspect and replace those components separately

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing

This mount is a replacement support bracket that secures internal components and helps keep assemblies aligned for reliable operation. Replacing a damaged mount restores proper fit and reduces vibration and noise from loose parts. What it does:

• Secures and supports appliance panels or internal assemblies to maintain proper alignment
• Prevents movement that can cause rattling, vibration, or uneven operation
• Helps ensure connected components stay in the correct position for normal function
• Commonly used when mounts are cracked, bent, or missing

• Disconnect power (and water if applicable) before starting any repair
• Use basic hand tools; inspect surrounding fasteners and replace if damaged
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection
• Replace all affected mounts for best results

The Canopy Mica is an OEM part for GE microwaves. This part covers the waveguide channel, preventing food particles and grease from entering the microwave's internal mechanisms.  

Causes of a bad canopy mica can include exposure to high levels of moisture or grease, physical damage such as cracks or burns, and general wear and tear over time.  

Symptoms of a bad canopy mica include:

• Sparks or arcing during microwave operation
• Burn marks or discoloration on the mica sheet
• Unusual noises while the microwave is running
• Uneven cooking or heating of food

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This light trim is the plastic bezel that surrounds and secures the oven/microwave interior light, restoring a finished appearance and protecting the light assembly from debris. It helps the light stay properly seated and keeps the opening neatly covered. What it does

• Covers and secures the interior light housing so the bulb and socket stay in place
• Protects the light opening from grease, food splatter and debris
• Restores a finished, OEM look to the appliance interior
• Can be replaced when cracked, chipped, warped or when the light opening is exposed

• One light trim/bezel

• Disconnect power to the appliance before beginning any service
• Remove any damaged trim pieces and clean the mounting area before installing the new bezel
• Typically secures with snap tabs or a couple of screws—use appropriate hand tools and avoid overtightening
• If the light bulb or socket is damaged, replace those parts separately

This right-side door hinge assembly secures and aligns the refrigerator door, restoring smooth opening and proper closure. Replaces a worn or damaged right hinge to reduce sagging and improve door seal performance. What it does:

• Provides the mounting point and pivot for the refrigerator door on the right side
• Restores proper door alignment and prevents door sag or uneven gaps
• Helps maintain an effective door seal to protect interior temperature
• Fits as the factory replacement right hinge assembly for compatible GE refrigerators

• One right-side door hinge assembly

• Support the door while removing/installing the hinge to avoid injury or damage
• Keep fasteners and hinge orientation consistent with factory locations; adjust alignment as needed
• Disconnect power to the appliance before starting work

This turntable motor drives the glass tray in your microwave for even heating. Replace it when the tray stops turning, turns intermittently, or the motor makes unusual noises to restore smooth, reliable rotation.

• Rotates the turntable tray/plate for more even cooking and reheating
• Provides steady drive to the tray via the center coupler
• Typical fix for a non-spinning or intermittently spinning turntable
• Can address loud humming or grinding noises from beneath the oven floor

• Disconnect power before servicing; microwaves contain high-voltage components
• Access is typically from the bottom by removing the motor cover or base panel
• Note wire orientation; transfer connectors, align the shaft with the coupler, and secure with the original screws
• After reassembly, place a microwave-safe cup of water on the tray and run briefly to ensure the turntable rotates