Parts for Kenmore 721.62462200 (72162462200, 721 62462200): Oven Interior Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Mounting screw for ovens, ranges, and microwaves. Secures panels, brackets, and internal components. Replace if stripped, missing, or damaged.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

The Door Latch Hook is an OEM replacement part for LG microwaves. Located internally on the door frame, this metal hook secures firmly into the microwave's door latch bracket when closed. As a common wear point, the hook can experience minor warping over many years of use.

Causes of a bad door latch hook include normal wear and tear, loss of tension, or deformation from frequent door opening and closing cycles long-term.

Symptoms of a bad latch hook include:

• Door that does not close fully or completely latch in place  
• Gaps forming in the door seal when shut
• Inability to achieve a tight, solid seal around the perimeter 
• Latch hook failing to grasp the bracket securely

This OEM LG part is also compatible with Sears/Kenmore microwaves. 

Fastens panels, brackets, and covers inside the microwave cabinet. Replace if cracked, broken, or missing to restore secure mounting and alignment.

This is a wire holder clip used inside a microwave to secure and route internal wiring. It keeps wires organized and safely positioned away from heat sources and moving components. Replace this holder if it is broken or missing, which can allow wires to hang loose and potentially contact hot surfaces or interfere with other parts.

Turntable stopped turning or making noise? This microwave motor rotates the glass tray for even heating. Easy DIY fix with basic tools in under an hour.

Fix a microwave that won't start or runs with the door open. This door interlock switch ensures safe operation by detecting when the door is fully closed.

Microwave won't heat but runs normally? A failed magnetron is the likely cause. This part generates the microwaves that cook food. Moderate DIY repair.

Microwave won't heat or makes loud buzzing noise? The diode regulates magnetron current flow. Simple repair—test with multimeter for continuity.

This thermostat controls refrigerator temperature to help maintain proper cooling and prevent spoilage. It replaces a failed or inaccurate temperature control to restore consistent operation. What it does:

• Senses internal temperature and signals the compressor to cycle on/off
• Helps keep food at steady, safe temperatures when functioning correctly
• Commonly replaces thermostats that cause warm temperatures or inconsistent cooling
• Works as a direct replacement when matching the OEM part number

• Always disconnect power to the appliance before servicing to avoid shock or injury
• Handle the sensor and terminals carefully; avoid bending or damaging components
• Basic hand tools are typically required; follow your model's service manual for exact instructions

Replace your microwave door seal cushion to restore proper door closure and prevent heat loss. Essential when the seal is worn, cracked, or loose. Verify fit with your model number before ordering.