Parts for Frigidaire GLSE62RFW0: 04 - P17c0045 Control Panel Parts

Fix a dryer that won't turn off or advance through cycles with a new timer. Controls cycle duration and automatic shutoff. Moderate DIY repair.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Color: white. Measures about 1-1/2 inches in diameter.

Fix a washer that won't advance through cycles or stays stuck on one setting. This mechanical timer restores proper cycle sequencing. 1-hour DIY repair.

Replace your dryer's broken or missing start knob. This control dial installs on the front panel to restore operation of the start cycle function.

This push start switch is the user-operated momentary button that completes the start circuit so the appliance begins its cycle. It replaces a worn or unresponsive start button to restore reliable start control. What it does:

• Acts as a momentary contact to send the start signal to the control
• Commonly used when the appliance does not begin a cycle after pressing the start button
• Can fail from wear, corrosion, or broken actuator, causing no response or intermittent starts
• Works with the factory wiring and mounting for direct replacement

• One push start switch

• Always disconnect power to the appliance before performing service
• Handle terminals carefully; ensure secure, corrosion-free connections
• Test the switch for continuity with a meter after installation and before restoring full use

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

The dryer timer power resistor regulates electrical current to the timer motor in mechanical timer systems. Replace when the timer fails to advance properly, gets stuck in cycles, or the dryer runs continuously without stopping.

Replacement timer knob for washer dryer combos. Mounts to the control timer shaft to select cycles and settings. Needed when original is cracked or stripped.

Mounting screw secures panels, trim, or brackets in dryers, washers, and ranges. Replace lost, stripped, or corroded screws to restore stability.

PPH ab st/z/ch `6 - 18x.60

Right endcap for washer dryer combo units. Covers and protects the right side panel edge. Replace if cracked, broken, or missing for a complete look.

Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.

The buzzer switch creates an audible signal when the drying cycle is complete, located on the dryer's control panel. Replace if the buzzer doesn't sound at cycle end, sounds continuously, or makes weak/distorted tones.

This replacement control panel bezel restores the front trim around a range or oven control area, providing a finished look and protecting underlying controls from spills and wear. It matches black trim with white printed markings for a clean, readable appearance. What it does:

• Covers and protects the control area and underlying components from spills, dust, and everyday wear.
• Restores damaged, faded, or cracked front trim so controls are clearly labeled and accessible.
• Helps keep control buttons and switches aligned and secure behind the trim.
• Improves the appliance's appearance when the original bezel is scratched or discolored.

• One control panel bezel (black with white print)

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Typically installs with a few screws or clips after removing the outer trim; handle gently to avoid cracking the plastic.
• Use appropriate screwdrivers and keep fasteners secure; do not overtighten.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.