Kenmore Refrigerator 253.71122104 (25371122104, 253 71122104) Parts

This door gasket presses into slot around door pull off old and press in new a five minute repair Read more

Well, I got online and found several YouTube videos on how to check what was happening. I have a multimeter and tools. I first replaced the external water filter just to make sure it wasn't that, and it needed it. That wasn't the problem. I then removed the water inlet valve which was really easy. I didn't disconnect the water lines but I did unplug the power plug. Using the ohms setting on the meter, I tested the coil of the valve solenoid. It wasn't open. I checked the voltage at the plug... Read more

Maybe 6 or 7 years ago I had a fridge conk out on me just before Christmas. It was loaded with food for the holiday, including a prime rib roast that was the hope and dream of the holiday for every red-blooded non-vegan in the house. In order to save the day I bottom-dollared a Frigidaire replacement. It performs well temperature-wise, but when it was only a couple years old the door handle cracked wide open. It was so delicate, you'd think that it was a movie prop "Break-Away Refrigerator... Read more

• Frost buildup
• Fridge runs too long
• Freezer too cold
• Freezer not defrosting

My problem first showed up as varying temperature in both sections of my old mid 1970’s Frigidaire model FPCI-170T-7 refrigerator, which is not listed on most appliance repair databases. Running on the warm side from time to time, as well as sudden fan noise (probably the fan blade hitting ice build-up on the evaporator coil) alerted me to a possible defrost system problem, since the compressor was cooling. The evaporator fan eventually failed after a day or so, and a major repair was... Read more

• Ice maker not making ice
• Leaking

This was one of the easiest appliance repairs that I have ever done. I simply moved the refrigerator out of the cubby hole in which it resides, turned off the water supply at the wall, unplugged the electric cord, loosened the water supply line at the valve (had a water absorbent rag and small plastic bowl to catch what drained from the line), place it in the bowl and moved it aside. The valve was easily accessible and two screws detached it from the edge of the refrigerator box. Once loose, I... Read more

• Freezer not defrosting
• Fridge too warm
• Freezer section too warm

This was a 2000 model so rather than just replace the defrost timer which was visibly burnt on the terminals, we just did everything. The cold control, defrost timer, thermostat, defrost heater and the compressor capacitor were all replaced. I had the same issue on my older unit and tore it apart replacing one item at a time over a three month period so on an older one i suggest do it all while it is apart. Read more

• Fridge too warm

Fan motor went bad. Fixed the fridge for less than it would have cost me just to have someone come out and look at it. Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

• Noisy

1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more

I removed the meat drawer and shelving unit. I unscrewed the Philips head screws on either side of the shelf brackets. I cleaned the old surfaces and fitted the new plastic hangers in place. I screwed the new hangers in place with the screws I had from the old ones. It was very easy, except the holes in the plastic hanger are not quiet big enough for the screws. I had to push very hard with the screwdriver, and started to strip the head of the screw as well at the screwdriver itself. I did... Read more

This was a 2000 model so rather than just replace the defrost timer which was visibly burnt on the terminals, we just did everything. The cold control, defrost timer, thermostat, defrost heater and the compressor capacitor were all replaced. I had the same issue on my older unit and tore it apart replacing one item at a time over a three month period so on an older one i suggest do it all while it is apart. Read more

Replaced two crisper drawers and a door shelf. The person who took my order was helpful and thorough in determining what I needed. The company was equally helpful when I needed to return some parts that I ordered which I turned out to not need. Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

Removed and replaced the gasket. Read more

I chated with a man on line and he had what I needed the picture did not show the sliders so I wasn't sure if it was the right one he assured me it was, got it in a few days very pleased with ApplianceParts Read more

FIrst, I removed the cardboard cover on the back, exposing the compressor compartment. I noticed the fan was not moving. I touched the blade and it immediately started spinning, but not very fast. The compressor was getting hot, and I think prob. overheating. The fan stopped after a few hours and then "froze" solid the next day. I got the parts and I followed the process in the video to replace the fan. VIdeo was right on the money. but there were some difficulties. The retention clip on the... Read more