Kenmore Dishwasher 665.13409K901 (66513409K901, 665 13409K901) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10282479
Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.
More
$20.95
- Compare At:
-
$24.72
- You Save:
-
$3.77
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8565925
Replaces cracked, broken, or missing dishwasher rack stop clips. Secures upper or lower dishrack to track rail, preventing rack from sliding out too far.
Do-It-Yourself Stories from Customers like You
Dishwasher would not discharge water John S. • Lebanon , NJ • August 15, 2015
My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep?
After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink.
A...
Read more
More
$9.41
- Compare At:
-
$11.10
- You Save:
-
$1.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WP661566
Thermostat has 1/4 inch terminals.
The High Limit Thermostat is an OEM part for Whirlpool dishwashers. This safety feature is designed to prevent the dishwasher from overheating by shutting off the power if the internal temperature exceeds a certain limit. It acts as a safeguard against potential hazards, such as fires, and ensures the dishwasher operates within safe temperature ranges.
Over time, the high limit thermostat can become defective due to normal wear or electrical issues within the dishwasher. A malfunctioning thermostat may not accurately respond to temperature changes, which can lead to overheating or the dishwasher not reaching the necessary temperature for optimal cleaning.
Symptoms of a bad High Limit Thermostat include:
- Dishwasher not starting or completing a cycle
- The dishwasher stops heating water, affecting cleaning performance
- Overheating, which could potentially damage dishes or the dishwasher itself
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Not drying dishes properly
See more...
Do-It-Yourself Stories from Customers like You
Whirlpool dishwasher not fully cleaning or drying dishes. Andrew M. • Seattle , WA • January 05, 2020
My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished.
I decided to...
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10509257
The Door Gasket is an OEM part for Whirlpool dishwashers. This gasket is designed to create a watertight seal around the dishwasher door, preventing water from leaking out during wash cycles. It ensures that the dishwasher operates efficiently by keeping water inside the unit, maintaining optimal cleaning performance, and protecting your kitchen from water damage.
Causes of a bad door gasket can include regular wear and tear from frequent use, exposure to high temperatures and harsh detergents, or damage from debris and foreign objects. Over time, these factors can lead to the gasket becoming brittle, cracked, or deformed, compromising its sealing ability.
Symptoms of a bad door gasket include:
- Water leaking from the dishwasher door during or after a cycle
- Visible cracks, tears, or deformities in the gasket
- The dishwasher door not closing properly or requiring extra force to close
- Mold or mildew buildup on the gasket
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Dishwasher was leaking from the bottom front Alicia M. • Morganton , NC • January 12, 2015
I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future.
Read more
More
$55.95
- Compare At:
-
$67.14
- You Save:
-
$11.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP717273
The Rubber Washer is an OEM part for Whirlpool dishwashers. This washer plays a role in ensuring a leak-proof seal at various connection points within the dishwasher, such as at the water inlet valve or hose connections. Its primary function is to prevent water from leaking out of the dishwasher during operation, thereby ensuring efficient and safe use of the appliance.
Over time, rubber washers can deteriorate due to the constant exposure to water and chemicals found in dishwasher detergents.
Symptoms of a bad Rubber Washer in a dishwasher include:
- Visible signs of wear or damage to the washer, such as cracks, brittleness, or deformation.
- Water leaking from the dishwasher, particularly around areas where hoses and valves connect.
- A decrease in dishwasher performance due to water not being contained properly during cycles.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
This part fixes the following symptoms
-
Not drying dishes properly
See more...
Do-It-Yourself Stories from Customers like You
Dishwasher not heating. Ben M. • Sacramento , CA • February 18, 2020
Replaced heater element: Once I had the dishwasher out of the cabinet with supply hose, drain hose and electric disconnected, removing the heater element was fast and easy. However, it was confusing that the new heater element had rubber washers on it already, something not mentioned in the product listing, although kinda visible in the photo. I ordered the separate rubber washer parts recommended by Appliance Parts Pros together with the heater element. The separate rubber washers were the...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 675806
Standing water in dishwasher bottom or leaking onto floor? This impeller and seal kit repairs worn bushings and seals. 15-minute DIY fix.
Do-It-Yourself Stories from Customers like You
Repeated failure of the pump/drain system which was usually preceded by a "buzzing/grinding" noise culminating in a failure to drain Lawrence R. • Parma , OH • June 04, 2017
I had previously disassemble the pump assembly to find what I at first thought was an oddly shaped spring, which it was. What I learned by researching the parts was that the spring's odd shape was a result of something having gotten caught in the pump and jamming the impeller.
After ordering the parts, I watched the "repair video" a few time and proceeded to remove and replaced the affected parts. Reassembly went pretty much as described with the one small glitch being the seating of the new...
Read more
More
$102.95
- Compare At:
-
$122.51
- You Save:
-
$19.56
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9742946
Nylon radial ring bearing supports the spray arm hub in your dishwasher. Replace if cracked, worn, or broken to restore proper spray arm rotation.
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3376846
Ring bearing supports spray arm rotation in dishwashers. Mounts at spray arm base to allow free spinning. Replace if cracked, worn, or missing.
This part fixes the following symptoms
-
Not cleaning dishes properly
See more...
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$11.51
- Compare At:
-
$13.70
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11752368
This dishrack replaces a damaged, rusted, or warped rack to restore smooth loading and secure support for dishes. A solid rack keeps items upright for better spray coverage, cleaner results, and helps prevent rust transfer and chipping.
- Holds and organizes plates, bowls, and cookware for proper spacing and spray access
- Provides stable support to reduce tipping and breakage during wash cycles
- Replaces racks with rust, broken wires, or bent/missing tines
- Can help resolve issues like rust marks on dishes and loading difficulties
What's included: 1 dishrack Install notes:
- Disconnect power at the breaker before servicing
- Open the door; slide the old rack out—on some models, release rack stops to remove
- Transfer any reusable accessories from the old rack to the new rack if applicable
- Wear cut-resistant gloves; set the new rack on the rails and verify smooth movement and proper door closure
Do-It-Yourself Stories from Customers like You
Rusted Armando G. • Gilbert , AZ • April 26, 2025
Good
Read more
More
$155.79
- Compare At:
-
$173.10
- You Save:
-
$17.31
Genuine Whirlpool part
By: Whirlpool
Part Number: 675813
The Thermal Fuse is an OEM part for Whirlpool dishwashers. It serves as a crucial safety component that prevents the appliance from overheating by cutting off electrical power if the temperature inside the dishwasher becomes too high. This helps protect both the dishwasher and your home from potential fire hazards.
Causes of a bad thermal fuse can include overheating due to blocked air vents, malfunctioning components that lead to excessive heat, or electrical surges that damage the fuse. Over time, regular wear and tear can also contribute to the fuse's failure.
Symptoms of a bad thermal fuse include:
- The dishwasher not starting or running
- The control panel not responding
- The dishwasher stopping unexpectedly mid-cycle
- No indicator lights or sounds when attempting to operate the dishwasher
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Dishwasher just stopped working, no power Michelle W. • Gillett , WI • April 05, 2014
My friend researched online what would make a dishwasher just stop working, no power. The person on the you tube video showed how to first start with the thermal fuse. Then searched online for the thermal fuse. You had the part for a small price. I felt it was worth trying to see if that may be the issue. IT WORKED!! I was without a dishwasher for over a year, was planning to by a brand new one but for $23.00 now have a working dishwasher!! YEAH!
Read more
More
$49.55
- Compare At:
-
$58.96
- You Save:
-
$9.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268873
Plastic nut that secures the lower spray arm to the dishwasher mount. Replace if broken, cracked, or threads are stripped to keep the spray arm in place.
Do-It-Yourself Stories from Customers like You
Sprayarm nut threads broke off in the sprayarm mount Thomas H. • Haughton , LA • March 12, 2014
Removed 8 hex screws and the cap to remove the broken threads...used needle nosed pliers for this, stuck them in and expanded them to put pressure on the thread sleeve from the inside, as threads were broken off below the edge. Replaced all very simply
Read more
More
$9.41
- Compare At:
-
$11.29
- You Save:
-
$1.88
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10204131
Replace cracked or broken dishwasher rack roller axle assemblies. Installs on upper or lower dish racks to restore smooth gliding. Includes clips.
Do-It-Yourself Stories from Customers like You
Broken rollers. Roger H. • Brownstown , IN • July 11, 2017
Snaped off and snaped on.
Read more
More
$9.41
- Compare At:
-
$11.20
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8066018
The Detergent Lid Spring is an OEM part for Whirlpool dishwashers. It is responsible for providing the necessary tension to open and close the detergent dispenser lid during the wash cycle.
Over time, the detergent lid spring can wear out, lose tension, or break due to repeated use, exposure to water and detergent, or accidental mishandling. If the spring becomes faulty, the dispenser lid may not function properly, leading to poor washing results.
Symptoms of a bad detergent lid spring include:
- Detergent dispenser lid not opening during the cycle
- Difficulty in closing the dispenser lid
- Inconsistent or incomplete release of detergent
- Visible damage or wear on the spring
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
For the complete detergent dispenser kit order 4387043.
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: W10161215
The Dishrack is an OEM replacement part for Whirlpool dishwashers. It measures 21" wide x 21" deep. It provides a stable framework for organizing and holding dishes, glasses, utensils, and other items during the washing cycle. Designed to fit securely in the dishwasher, it ensures proper water flow and cleaning efficiency for all loaded items.
Causes of a bad Dishrack can include prolonged exposure to high temperatures and moisture, leading to rust or corrosion, damage to the coating from sharp utensils, or bending or breaking due to heavy or improperly loaded items. Over time, these issues can compromise its functionality.
Symptoms of a bad Dishrack include:
- Rust or peeling coating on the rack
- Broken or bent tines that can’t hold dishes properly
- Difficulty sliding the rack in and out of the dishwasher
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Coating was coming off allowing rust to form and leave marks on dishes Waldo G. • Wichita , KS • December 30, 2014
Replaced the lower rack
Read more
More
$306.95
- Compare At:
-
$365.27
- You Save:
-
$58.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 72017
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Do-It-Yourself Stories from Customers like You
Chipped paint Thomas S. • Middletown , DE • September 03, 2014
Touch up paint
Read more
More
$11.51
- Compare At:
-
$13.70
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 350930
Color: White. Size: 13 oz can. Acrylic appliance aerosol can spray paint.
The Appliance Spray Paint is an OEM part for Whirlpool appliances, designed to provide a quick and effective way to touch up or completely refinish the exterior of various appliances. This specialty spray paint is formulated to adhere to metal surfaces, offering a durable and resistant finish that can withstand the routine wear and tear of kitchen environments, including heat, moisture, and everyday use.
The primary reason for using such a specialized paint is to maintain or restore the aesthetic appeal of your appliances while protecting them from further damage.
Symptoms needing for Appliance Spray Paint include:
- Scratches, chips, or rust spots on the appliance's exterior that can lead to further damage or corrosion if left untreated
- A desire to refresh or update the appearance of the appliance without the need for complete replacement
- Discoloration or fading of the original finish due to age, exposure to sunlight, or cleaning agents
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99