Kenmore Range 790.46102300 (79046102300, 790 46102300) Parts

• Oven is too hot
• Oven not heating evenly
• Little to no heat when baking
• Won't start

Bought a used Frigidaire 36 inch stove. The broiler didn't come on but the burners lit and the stove worked so I made do for about 4 or 5 years with that. Then the F10 code came up and it wouldn't stop beeping until I unplugged it. I figured the electronics/circuit board was probably bad and ordered a replacement. I was confused about what part to order. The parts list includes "Control Panel" and "Clock - Timer". Turns out the control panels are the glass panel on the front of the stove... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

One day, while trying to roast chicken on the convection roast setting, my Electrolux oven stopped heating properly. I tried the broil setting and the top electric heating element worked fine. I then tried the bake setting and found that the bottom element wasn't working at all. I Googled the problem. The info I found said that the issue was probably that the bake element needed to be replaced. It said to look for a break or burned through spot on the element. If it appeared OK, remove it... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

• Little to no heat when baking
• Won't start

We replaced the broken Terminal Block but have not yet replaced the Control Panel. Will purchase that part from you shortly. Read more

• Element will not heat
• Little to no heat when broiling
• Oven not heating evenly

With my tools Read more

Had to pull double oven and range top out from wall which involved removing the upper kitchen cabinet. Took the sheet metal off the back and had the socket swapped out in a couple of minutes. My old oven works like a charm! Read more

• Element will not heat

Replaced infinite switch on large burners and just went ahead and replaced the infinite switch on the small burners while I had it apart and installed all new surface elements as well...parts were shipped the next day and I received them within 2 days... Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

I replaced the Switch for the burner. Works fine. Read more

When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged... Read more

Bought two new racks - beautiful! Bought replacement door seal: watched simple video and installed new seal in less than 10 minutes. Extremely pleased and impressed with entire experience as a first-time customer. Read more

Replacing the trim takes a little bit of alignment and light force. The trim slides over the glass panel of the door, with the glass sliding into plastic tabs. We kept the door nearly vertical (almost closed), lined up the tabs on the trim with the glass door, and used mild force to slide the trim down onto the glass door. (Also, we found that the tabs on trim we ordered were much bigger than the tabs on our broken trim. This is probably due to slight variations in Frigidaire's design over... Read more

Replaced the rear rollers. Video of job on your website made it easy. Read more

Replaced infinite switch on large burners and just went ahead and replaced the infinite switch on the small burners while I had it apart and installed all new surface elements as well...parts were shipped the next day and I received them within 2 days... Read more

Lightning Delivery - inserted and used a hammer and screwdriver to tighten unit...... Read more

• Door won't open after self cleaning cycle

Replace door lock motor and switch assy Read more