Kenmore Range 790.78510401 (79078510401, 790 78510401) Parts

• Gas smell
• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

My Tappan Range, which I paid a grand total of $65.00 for, and have been using since Katrina, (Katrina in 2005 is how we measure time in South Mississippi.) I live in an old house, and I am old, too. Last winter was the coldest I can remember, and my husband (older than I and far more hard-headed) used the oven like a heater. I read all user's manuals, because I use only used stuff, I can download the manuals or read them online, and it clearly stated in there NOT to use the oven as a... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

I replaced the probe which is a thermocouple. Naturally the connector was different from the one on the stove so I cut off the connector on the old probe and soldered it to the new probe. The cleaning of the wires and soldering them was the most time consuming activity of the repair. My wife just tried the stove and the oven temperature read exactly as the setting. Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

• Won't start

Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more

The clips on the rear side of the drawer box were broken. Easy to locate the part on the website. Part in hand in two days and installed in about five minutes. Needed to remove the drawer and use a 1/4" driver, remove the broken slide and install the new one. Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

The bottom drawer glides tend to wear. The metal drawer sliding against the plastic glide creates a groove. After only a couple years, the groove was so large that the drawer slid in too far. It was no longer flush with the oven door. Then the left side was crooked!!! All it took was a screw driver to install these new glides. Read more

Had to pull double oven and range top out from wall which involved removing the upper kitchen cabinet. Took the sheet metal off the back and had the socket swapped out in a couple of minutes. My old oven works like a charm! Read more

Watched repair video's to learn where parts were located. Put replacement in and it worked great! Read more

Bought new burner tops for all four burners. Lights great now with nice blue flames and no yellow. Read more

Bought new leveling leg. Took longer to lay the appliance on the side and pick back up, than to install leg. Read more

I installed a new clock timer and overlay the job took only a few minutes and a very easy repair. Useful hint take a picture of your clock timer before you start to make sure all your wires are put back in the right order . Charles B Lafayette Tn Read more

I had to order the glass, frame, and cap that the handle attaches to. I just had to put in about 6 screws, it was very simple. Read more

Easy just pull clip and put back Read more