Kenmore Range 790.7965370A (7907965370A, 790 7965370A) Parts

My Kenmore 790.74139310 gas range was taking over 30 minutes to reach 350F. It used to take a little less than 10 minutes. The problem was the ignitor for the lower gas burner. It would glow but not pass sufficient current to increase the gas flow to the lower burner. Once at temperature, there is of course loss of heat when loading the oven with room temperature food. This took too long to recover, so we did not have proper temperature for proper cooking for the first 30 to 40 minutes. Food... Read more

After I came from from work, my wife told me about the problem. I quickly began to research the code F10 which according to the paper in the pouch behind my range said it needed a new temperature control sensor and that should fix it. It also said that if that doesn't fix the problem that I'd have to replace the circuit board which probably got fried due to the runaway temperature. So, I decided to just order the temperature sensor part# AP3963654 for $25.63 plus shipping. I ordered the part at... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

Replaced ignitor. Very simple project. Read more

I ordered this glass and used a youtube video to replace the shattered glass step-by-step. I was a bit wary of doing this work myself, but it proved to be a snap. Within an hour of finding this package on my front porch, I had the oven as good as new. Read more

• Door won't close

I purchased two screws (316433300) and the handle (316443602). Screws and handle are exact replacements of old parts that wore out. I was hoping the screw would be longer, but so far it works perfectly. I will keep you posted if it wears out again in the near future. Thanks ApplicancePartsPros.com — this was an easy fix! Read more

Thanks, I’ follow the instructions on YouTube and my repairs was completed. Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

Order the part from you all. Watched the video how to install, which was easy to understand. the part arrived A DAY EARLIER than we expected! How nice is that? and installed part, stove /oven works. everybody's happy. Read more

The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should. Read more

Called for a repair tech, he told me what the problem was, I had already checked out the burnt connections,repair was going to be $450-500 range, My wife & I discussed repair or new range,repair won out.I am a retired machine repairman with some elect skills,so looked up parts online ordered them, installed the new control board with the new "decal" , checked out the oven, etc, everything seems good to go. This range is only 6.5 yrs old , they don't seem to make them last as long as the ones I... Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

I purchased the lens cover from your on-line store. It came within the week. I was able to change the lens cover without any problems. My husband takes care of things like this for me at home, but this cover was for my mother's oven. I broke the one she had when I was cleaning her oven and changing the bulb. Read more

I used the new screws; which were about 1/4 inch longer then OEM for better engagement, and with Phillips screw driver attached the handle. Read more