Kenmore Refrigerator 106.50228010 (10650228010, 106 50228010) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10312301
This is the complete horizontal ice dispenser bucket assembly with crusher. It fits 22 cubic foot refrigerator models. For 20 cubic foot models order WP2209778. For 25 and 27 cubic foot models order WPW10312300.
Do-It-Yourself Stories from Customers like You
Auger that dispences the ice was not working like it should Louis R. • Bay City , TX • June 13, 2014
I ordered the complete assembly ice bucket and all
Read more
More
$228.43
- Compare At:
-
$271.83
- You Save:
-
$43.40
Genuine Whirlpool part
By: Whirlpool
Part Number: W11496481
The Water Tube is an OEM component specifically designed for Whirlpool refrigerators. This 1/4" diameter water tube provides a pathway for water to flow through the refrigerator's internal components during operations like ice production.
Causes of a bad water tube can include cracks or defects from manufacturing, damage from impact or abrasion during shipping or installation, or wear over time from cycles of use.
Symptoms of a bad water tube include:
- Water leaks or drips inside the refrigerator
- Insufficient or slow water flow to components
- Abnormal sounds from water not flowing smoothly
- Failure of components dependent on water flow like the ice maker
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore refrigerator models.
Do-It-Yourself Stories from Customers like You
Water filter housing leaking H M. • Picayune , MS • August 18, 2015
Replaced filter housing, and both water tubes
Read more
More
$26.95
- Compare At:
-
$31.80
- You Save:
-
$4.85
Genuine Whirlpool part
By: Whirlpool
Part Number: W11512417
The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan.
Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.
Symptoms of a bad drain connector include:
- Water or condensation leaks around the connector area
- Puddles or watermarks on the floor behind the fridge
- Slow drainage of water from the evaporator fan coil
- Mold or mildew growth near the connector or drain area
This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The problem was ice buildup on the floor of the freezer William B. • Pahoa , HI • January 15, 2016
A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction....
Read more
More
$25.95
- Compare At:
-
$31.14
- You Save:
-
$5.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10224328
For the complete ice door kit order W10823377.
Do-It-Yourself Stories from Customers like You
Ice dispenser chute door was not closing or sealing Robert H. • West Palm Bch , FL • July 23, 2025
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable...
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: W10852691
This baffle sits in the ice bin and supports the auger so ice feeds smoothly to the dispenser. Replace a cracked or worn baffle to restore reliable dispensing and reduce jams or grinding from the ice bucket.
- Supports and aligns the ice auger inside the bin
- Guides cubes/crushed ice toward the crusher/dispenser
- Helps prevent auger wobble, binding, or excessive noise
- Failure can show as weak/no ice dispensing or intermittent jams
What's included: 1 baffle Install notes:
- Disconnect power; remove the ice bin from the freezer/door
- Empty the bin and remove any screws/clips securing the baffle
- Transfer any reusable hardware; orient the baffle correctly around the auger
- Tighten fasteners without overtightening; reinstall bin and test dispense
Do-It-Yourself Stories from Customers like You
The ice crusher mechanism on my ice maker wasn't working properly i was getting bits of white plastic in my ice so obviously something was broken in there Tawna M. • Orem , UT • July 27, 2015
I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again.
Read more
More
$25.95
- Compare At:
-
$30.62
- You Save:
-
$4.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671B
Color: black. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
Stopped dispensing water Cristopher C. • Santa Rosa , CA • July 15, 2016
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey.
Read more
More
$55.38
- Compare At:
-
$65.35
- You Save:
-
$9.97
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152859
Color: Black
Do-It-Yourself Stories from Customers like You
Refrigerator water dispenser stopped working Carlos R. • Houston , TX • September 19, 2014
The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place...
Read more
More
$51.28
- Compare At:
-
$61.02
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking water filter housing and broken grill cover clips Carl H. • Strongsville , OH • December 04, 2016
Ordered parts, watched the videos on your website. Very simple.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10304659
Note: Right Hand Roller
Do-It-Yourself Stories from Customers like You
Rollers under refrigerator were worn and/or broken Tim C. • Pasadena , MD • February 28, 2020
Lifted refrigerator in front and back. Removed roller pin holding assembly. Removed defective assembly and replaced with new.
Read more
More
$55.37
- Compare At:
-
$66.44
- You Save:
-
$11.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10304660
Note: Left Hand Roller
Do-It-Yourself Stories from Customers like You
Rollers under refrigerator were worn and/or broken Tim C. • Pasadena , MD • February 28, 2020
Lifted refrigerator in front and back. Removed roller pin holding assembly. Removed defective assembly and replaced with new.
Read more
More
$55.37
- Compare At:
-
$65.89
- You Save:
-
$10.52