Kenmore Refrigerator 106.52514100 (10652514100, 106 52514100) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2188755
The Rear Access Cover is an OEM part for Whirlpool refrigerators. It protects the rear components of the refrigerator, such as the compressor, condenser coils, and electrical connections, ensuring these vital parts are shielded from dust, debris, and potential damage while still allowing for necessary ventilation.
Causes of a bad rear access cover can include wear and tear from prolonged use, accidental impacts that cause cracks or breaks, or damage during maintenance or repairs.
Symptoms of a bad rear access cover include:
- Cracks or visible damage to the cover
- Difficulty securing the cover in place
- Excessive dust or debris around internal components
- Rattling or noise from a loose cover
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking water at the water intake valve. Christy C. • Warner Robins , GA • May 01, 2020
My 16 year old son ordered the part and replaced the part. It took him less than 5 minutes to replace the part.
Read more
More
$83.35
- Compare At:
-
$98.35
- You Save:
-
$15.00
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152858
Color: White
Do-It-Yourself Stories from Customers like You
The ice dispenser lever was cracked and did no longer trigger the dispensing of the ice Andrea M. • Honolulu , HI • March 01, 2015
I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better.
I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some...
Read more
More
$53.33
- Compare At:
-
$64.00
- You Save:
-
$10.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387835
This refrigerator compressor starting device includes the start relay, overload and cover.
Do-It-Yourself Stories from Customers like You
Lights on not cooling James S. • San Jose , CA • September 08, 2014
Took the screws off the back plate at the bottom and watched the YouTube video on how to remove the cover plate for the starter and overload on the back of the compressor. Ended up snapping the old cover plate (brittle plastic) so I was glad the "kit" came with a new one. I used a small flat-head screwdriver and carefully pried off the starter and overload, then, with the new ones in hand, took the wires off the old ones and immediately put them on the new ones so I didn't lose track (there is...
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10224328
For the complete ice door kit order W10823377.
Do-It-Yourself Stories from Customers like You
Ice dispenser chute door was not closing or sealing Robert H. • West Palm Bch , FL • July 23, 2025
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable...
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196175
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Oven drawer wouldn’t slide properly. Nick B. • Hanover , MD • November 09, 2020
Whenever the drawer was opened, it would fall of the guide rails. This lead to the drawer being crooked several times. I took the drawer out and noticed one of the glides was missing. Ordered a new pair, popped it on and now the drawer slides properly.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W10852691
This baffle sits in the ice bin and supports the auger so ice feeds smoothly to the dispenser. Replace a cracked or worn baffle to restore reliable dispensing and reduce jams or grinding from the ice bucket.
- Supports and aligns the ice auger inside the bin
- Guides cubes/crushed ice toward the crusher/dispenser
- Helps prevent auger wobble, binding, or excessive noise
- Failure can show as weak/no ice dispensing or intermittent jams
What's included: 1 baffle Install notes:
- Disconnect power; remove the ice bin from the freezer/door
- Empty the bin and remove any screws/clips securing the baffle
- Transfer any reusable hardware; orient the baffle correctly around the auger
- Tighten fasteners without overtightening; reinstall bin and test dispense
Do-It-Yourself Stories from Customers like You
The ice crusher mechanism on my ice maker wasn't working properly i was getting bits of white plastic in my ice so obviously something was broken in there Tawna M. • Orem , UT • July 27, 2015
I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again.
Read more
More
$25.95
- Compare At:
-
$30.62
- You Save:
-
$4.67
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2203771
The Top Hinge is an OEM part for Whirlpool refrigerators. This hinge ensures the proper alignment and smooth operation of the refrigerator door, allowing it to open and close securely. It supports the weight of the door and helps maintain an airtight seal.
Causes of a bad top hinge can include general wear and tear, heavy use, or accidental damage.
Symptoms of a bad top hinge include:
- Refrigerator door sagging or misaligned
- Difficulty in opening or closing the door
- Door not sealing properly, leading to temperature fluctuations
- Unusual noises when the door is operated
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Needed hinges for doors William H. • Niles , MI • September 22, 2015
Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot
Read more
More
$51.26
- Compare At:
-
$61.00
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2195915
Color: white. Measures about 2-1/2 inches high by 5 inches deep.
Do-It-Yourself Stories from Customers like You
Needed parts Evelyn W. • Brentwood , NY • August 01, 2016
It was easy replace broken with new one snap on and off easy
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2174267
The Wire Shelf is an OEM part for Whirlpool refrigerators. It is designed specifically for the freezer compartment of the refrigerator. It is constructed with wire material to support the weight of various frozen food items without bending or sagging.
Causes of a faulty freezer shelf can include wear and tear over time, damage from heavy or improperly placed items, or bending due to excessive weight.
Symptoms of a bad freezer shelf may include:
- Sagging or bending of the shelf surface
- Instability or wobbling when placing or accessing items on the shelf
- Reduced storage space or difficulty in organizing frozen food
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
I needed a new shelf for my freezer Michael G. • Toledo , OH • July 22, 2016
I ordered one from you.
Read more
More
$59.95
- Compare At:
-
$71.34
- You Save:
-
$11.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10250570
This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:
- Supports the refrigerator cabinet and helps maintain proper leveling
- Allows the unit to roll for easier cleaning and servicing
- Replaces worn, cracked, or seized rollers and damaged brackets
- Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge
What's included:
- One complete cabinet roller assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
- Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
- After installation, level the refrigerator and verify doors close and seal properly
Do-It-Yourself Stories from Customers like You
The plastic left rear wheel was coming apart and needed replacing Gary H. • San Antonio , TX • June 11, 2016
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The...
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking water filter housing and broken grill cover clips Carl H. • Strongsville , OH • December 04, 2016
Ordered parts, watched the videos on your website. Very simple.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2171713
This ice compartment door closes off the ice storage area inside the freezer, helping contain cold air and keep ice clean. Replace a cracked or warped door to restore a proper seal and easy access to the bin.
- Covers the ice compartment opening to help maintain temperature around the ice bin
- Hinged panel provides convenient access to the ice container
- Helps minimize frost and moisture at the compartment opening
- Common signs it's needed: cracked/missing door, broken hinge tabs, won't stay closed, frost buildup, or ice clumping near the opening
What's included: 1 ice compartment door Install notes:
- Disconnect power to the refrigerator before servicing
- Remove screws, pins, or clips securing the old door; note hinge orientation
- Transfer any reusable hinge pins, latches, or trim from the original if required
- Install and align the new door; confirm smooth operation and a tight closure
Do-It-Yourself Stories from Customers like You
Noisy water pipes in house when dispensing water slowy and squirting water dispensing Roger S. • Harker Heights , TX • August 18, 2016
Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,...
Read more
More
$53.32
- Compare At:
-
$63.45
- You Save:
-
$10.13